ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 52)

01 Activated By:

Zone List

Activated By

0 = delete

1 = zone list

2 = zone type

3 = zone number

[

∗

] to continue

Select where the initiating event for this output definition is to occur

as follows:

0 = delete (deletes the output function and any previous

programming;-see prompt below)

1 = zone list (go to “A” prompt)

2 = zone type (go to “B” prompt)

3 = zone number (go to “C” prompt)

If you enter “0,” the following prompt appears:

Delete?

Press 1 to delete this

0 = NO, 1 = YES

output definition

“

”

01 Zn List

Zone List

01-08 = zone list

[

∗

] to continue

If zone list was selected, this screen appears. Otherwise skip to the

next row.

Enter the desired zone list number associated with this output

number.

NOTE:

Do not use pager zone lists 09-12 in output definitions.

Press [

✱

] to continue.

Enter the zone list event that will activate this output.

Enter Event

0 = restore; 1 = alarm;

Alarm 1

2 = fault; 3= trouble

NOTE:

For alarm, fault, and trouble, an event on ANY zone in the

list activates the output, but ALL zones in the list must be restored

before the output is restored.

Press [

✱

] to continue and skip to the “Output Action” prompt.

“

”

01 Enter Zn type

Perimeter 03

Zone Type

see list at right

If zone type was selected, this screen appears. Otherwise skip to the

next row.

Enter the desired zone type associated with this output number. See

below for a list of available zone types.

CHOICES FOR ZONE TYPES:

00 = Not Used 05 = Trouble Day/Alarm Night 12 = Monitor Zone

01 = Ent/Exit #1 06 = 24 Hr Silent 14 = Carbon Monoxide

02 = Ent/Exit #2 07 = 24 Hr Audible 16 = Fire w/verification

03 = Perimeter 08 = 24 Hr Aux 23 = No Alarm Response

04 = Interior Follower 09 = Fire 24 = Silent Burglary

10 = Interior w/Delay 77 = keyswitch zone

81 = AAV Monitor Zone

90-91 = Configurable

CHOICES FOR

SYSTEM OPERATION:

20 = Arming–Stay 36 = **At Bell Timeout*** 52 = Kissoff

21 = Arming–Away 38 = Chime 54 = Fire Zone Reset

22 = Disarming 39 = Any Fire Alarm 58 = Duress

31 = End of Exit Time 40 = Bypassing 60 = AAV

32 = Start of Entry Time 41 = **AC Power Failure 66 = Function Key†

33 = Any Burglary Alarm 42 = **System Battery Low 67 = Bell Fail

43 = Comm. Failure 68 = Telco line cut

78 = keyswitch red LED

79 = keyswitch green LED

** Use 0 (Any) for Partition No. (P) entry.

*** Or at Disarming, whichever occurs earlier.

†

Use *57 Menu Mode to assign the function key (function “07”).

Note:

In normal operation mode:

Code + # + 7 + NN Key Entry

starts

Device NN.

Code + # + 8 + NN Key Entry

stops

Device NN.

Enter the partition in which this zone type will occur.

01 Partition 0 = any partition; 1 = partition 1;

Any partition 0 2 = partition 2; 3 = common

Press [

✱

] to continue and skip to the “Output Action” prompt.

Installation Instructions

6-4

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15