ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 14)

Installing the RF Receiver

Use any ADEMCO 5800 Series Wireless Receivers, such

as:

RF Receiver No. of Zones

5881L/5882L up to 8

5881M/5882M up to 16

5881H/5882H, VISTA-20P = up to 40 plus 16 buttons

5883, 6150RF VISTA-15P = up to 26 plus 8 buttons

1. Set Device Address to “00” as described in its

instructions (set all switches to the right, “off”

position).

2. Mount the receiver, noting that the RF receiver can

detect signals from transmitters within a nominal

range of 200 feet.

3. Connect the receiver's wire harness to the control's

keypad terminals. Plug the connector at the other

end of the harness into the receiver. Refer to the

installation instructions provided with the receiver

for further installation procedures regarding antenna

mounting, etc.

Notes

•

The receiver is supervised and a trouble report is

sent (“CHECK 100” displayed) if communication

between the panel and receiver is interrupted, or

if no valid RF signals from at least one supervised

transmitter are received within 12 hours.

If the receiver is mounted remotely:

•

Place the RF receiver in a high, centrally located

area for best reception.

•

Do not locate the receiver or transmitters on or

near metal objects. This will decrease range

and/or block transmissions.

•

Do not locate the RF receiver in an area of high

RF interference (indicated by frequent or

prolonged lighting of the LED in the receiver;

random flicker is OK).

•

Do not locate RF receiver closer than 10 feet

from any keypads to avoid interference from the

microprocessors in those units.

MOUNTING

HOLES

INTERFERENCE

INDICATOR

LED

CIRCUIT

BOARD

DIP SWITCH

PLUG

SOCKET

INSERT IN

RIGHT-HAND

TERMINALS

ANTENNAS

YELLOW

RED

BLACK

GREEN

}

TO CONTROL’S

REMOTE KEYPAD

CONNECTION

POINTS.

WIRING

OPENING

KNOCKOUT

AREA FOR

SURFACE

WIRING

5882

LOCATION

}

TO RELEASE CIRCUIT BOARD,

REMOVE SCREWS (2)

AND BEND BACK TABS (2).

MODEL No. IS INDICATED

ON CIRCUIT BOARD

NOTE: CIRCUIT BOARD IS MOUNTED IN

CONTROL’S CABINET, GROUNDING LUGS (2)

PROVIDED

MUST

BE INSERTED IN LEFT-

HAND TERMINALS OF ANTENNA BLOCKS AND

SECURED TO CABINET (SEE RECEIVER’S

AND CONTROL’S INSTRUCTIONS)

Figure 9. 5881/5882 RF Receiver (cover removed)

Installing a 5800TM Module

1. Mount the 5800TM next to the RF receiver (between

one and two feet from the receiver’s antennas) using

its accompanying mounting bracket. Do not install

within the control cabinet.

2. Connect the 5800TM to the control panel’s keypad

connection terminals as shown on the Summary of

Connections diagram and set to address 28.

Notes

•

Use this module only if you are using one or

more wireless bi-directional keypads or keyfobs

with a wireless Receiver; 5800TM is not

necessary if using a Transceiver (e.g., 5883).

•

The 5800TM must be set to address 28 (cut red-

W1 jumper).

•

The 5800TM can be used in partition 1 only.

•

For additional information regarding the

5800TM, refer to the 5800TM’s instructions.

Installing the Transmitters

1. To be sure reception of the transmitter's signal at the

proposed mounting location is adequate, perform a

Go/No Go Test, described in the Testing the System

section.

2. Install transmitters in accordance with the

instructions provided with each.

3. Set 5827, 5827BD, 5804BD wireless keypads to the

programmed House ID (field *24), using its DIP

switches (5827) or follow the instructions provided

with the device.

ULC NOTE:

In accordance with ULC standards, the

RF supervision period for the VISTA-20PCN and

VISTA-15PCN is three hours for Fire zones (Zone Type

9 and 16) and 12 hours for all other zone types.

Notes

•

Refer to the table of compatible devices at the

back of this manual.

•

Supervised transmitters

†

send check-in signals to

the receiver at 70-90 minute intervals. If at least

one check-in message is not received from each

transmitter within a 12-hour period, the “missing”

transmitter number(s) and “CHECK” is displayed.

†

Hand-held transmitters (e.g., 5802, 5802CP, 5804,

5804BD, 5827, 5827BD) do not send check-in signals.

The following transmitters are not intended for use

in UL installations: 5802MN, 5802MN2, 5804, 5804BD,

5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.

The 5827BD and 5800TM can be used in UL Listed

Residential Burglar installations.

IRELESS ZONE NUMBERS

ISTA-20P: transmitter zones 9-48

button zones 49-64

ISTA-15P: transmitter zones 9-34

button zones 49-56

Installation Instructions

2-8

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15