ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 12)

Hardwire Zones

Normally Open Zones/ Normally Open EOLR Zones

1. Connect open circuit devices in parallel across the

loop; for EOLR zones, connect the EOLR across the

loop wires at the last device.

2. Enable normally open/EOLR zones using Zone

Programming mode, “Hardwire Type” prompt.

Normally Closed Zones/Normally Closed EOLR Zones

1. Connect closed circuit devices in series in the high (+)

side of the loop; for EOLR zones, connect the EOLR in

series following the last device.

2. Enable normally closed/EOLR zones using Zone

Programming mode, “Hardwire Type” prompt.

Double-Balanced (V20P/PS only):

Connections as shown

(resistors not provided).

IMPORTANT:

Double-balanced zones provide zone tamper

protection, and should be used as burglary zones only. Do not

use double-balanced zones as fire zones.

Zone Doubling (V20P/PS only):

Connections as shown

(resistors not provided).

ZONE 3

ZONE 4

12 13

zone-002-V0

TAMPER

CONTACTS

TAMPER

CONTACTS

10 11

6.2k

ZONE 10

ZONE 2

zone-004-V0

Double Balanced Zones Zone Doubling

Notes

•

EOLR:

If the EOLR is not at the end of the loop,

the zone is not properly supervised and the

system may not respond to an “open” on the zone.

•

Zone 1 is intended for EOLR only.

For UL commercial burglar alarm

installations, use normally closed zones.

Zone Doubling (VISTA-20P/PS only):

This feature provides two hardwired zones for each

standard hardwired zone connected to the control’s

terminals (but does not increase the total number

of zones supported by the control). If enabled (Zone

Programming mode, “Hardwire Type” prompt,

option “3”), hardwire zones are automatically

paired as follows:

Zone Paired with zone

210

311

412

513

614

715

816

Note for Configurable Zone Types:

A short

across the EOL (i.e., at terminal) on either zone of

a zone-doubled pair or on a double-balanced zone

causes a tamper condition

Smoke Detectors

2-Wire Smoke Detectors

1. Connect up to sixteen (10, if “clean me” option used)

2-wire smoke detectors across zone 1 terminals 8 (+)

and 9 (-) as shown in the Summary of Connections

diagram at the back this manual. Observe proper

polarity when connecting the detectors.

2. Connect an EOL resistor across the loop wires at the

last detector.

Notes

•

Fire Verification (zone type 16):

The control

panel will “verify” a fire alarm by resetting the

smoke detectors after the first alarm trigger, and

then waiting 90 seconds for a second alarm

trigger. If the smoke detector or thermostat does

not trigger again, the control will disregard the

first trigger, and no alarm signal will occur. This

feature eliminates false alarms due to electrical

or physical transients.

SIA Installations:

If using fire verification on

zones other than zone 1, UL Fire Alarm Listed

relay accessories must be used to reset power as

described in step 3.

•

The zone 1 alarm current supports only one

smoke detector in the alarmed state.

•

Clean Me Option:

If enabled (field *174 = 1;

*56 zone programming, response time prompt =

3), certain ESL smoke detectors

†

send “clean me”

reports as appropriate. If used, the maximum

number of detectors is reduced to 10 (not

standard 16).

†Refer to the ESL documentation included with

the smoke detector for information regarding

compatibility with the clean-me option.

Installation Instructions

2-6

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15