ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 6)

Compatible Devices

• Supports up to 8 Addressable Keypads: 6150 Fixed-Word Display Keypad, 6160 Alpha Keypad,

6150V Fixed-Word Display Voice Keypad, 6160V Alpha Display Voice Keypad, 6150RF

Keypad/Transceiver

• Supports 4219, 4229 addressable hardwire zone expander modules (VISTA-20P = up to five for up

to 40 expansion zones; VISTA-15P = up to 2 for up to 16 expansion zones)

• Supports 5881 series receiver and 5800 series transmitters

• Output relays and/or Powerline Carrier Devices (X-10 type)

-- VISTA-20P = up to 16 relays/devices plus two on-board triggers

-- VISTA-15P = up to 8 relays/devices plus two on-board triggers)

-- Use any combination of 4204, 4229 and or Powerline Carrier Devices.

-- Output functions (up to 48)

• Ademco 4285/4286 Phone Module (Part. 1 only); provides access to the system via on premises or

off-premises phones for arming, disarming, etc., plus control of relay outputs and Powerline

Carrier devices.

• Audio Alarm Verification (using AAV module, such as Eagle Model 1250); can be used in

conjunction with an output trigger to permit voice dialog between an operator at the central station

and a person at the premises.

• Alarm output provides a 12VDC, 2 AMP output that can drive the compatible sounders; steady

output for burglary/panic, or temporal pulse (3 pulses – pause – 3 pulses – pause – 3 pulses. . .) for

fire. Uses current limiting circuitry for protection.

• Auxiliary Power Output: 12VDC, 600 mA maximum (uses PTC for protection).

• Backup Battery: Rechargeable (sealed lead-acid type) 12VDC, 4AH minimum.

• Long Range Radio: Primary telephone number messages can be reported via ECP connection to

various Long Range Radios (check compatibility and availability of specific models)

• AC Power Supply: Plug-in 120VAC transformer, ADEMCO 1321 or, if using Powerline Carrier

devices, ADEMCO 1321X10 or 4300 Transformer Module

NOTE: All devices and accessories used in a Canadian installation must be Listed for use in Canada.

Important Installation Highlights (Installer Please Read)

• This system uses addressable keypads and Zone Expander Modules (see table of addresses in

Programming Overview section).

• Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from

previous controls) and programmed in data fields *190-*196.

• Zone Expander Modules must be set for specific addresses (07-11), based on the zone numbers used

(see table of addresses in 4219/4229 Expansion Zones section).

• 4204 Relay Modules must be set for specific addresses (12-15; see Connecting Relay Modules

section).

• This control will not power-up unless AC power is connected (will not power-up on battery alone).

However, once the system is powered up, it will operate on battery power in the event of AC loss.

• Relays have two programming menu modes: Use *79 Menu mode to map module addresses and

device (output) numbers. Use *80 Menu mode to define the output functions (see Output Device

Programming section).

• This system supports programmable function keys. Use *57 Menu mode to define the function keys

(see Function Key Programming section).

• This system provides various paging features. Refer to the Programming Overview section for a

summary on pager programming.

Installation and Setup Guide

1-2

1 2 3 4 5 6 7 8 9 10 11 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15