ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 31)

FIELD TITLE and DATA ENTRIES EXPLANATION

*59

Exit Error Report Code

0 = no report

1-F = see description above

If the system is armed and an entry/exit or interior zone is still open

after the Exit Delay time has expired, an alarm will sound (keypad

displays “EXIT ALARM”). If the system is disarmed before the end of

the Entry Delay, the alarm sounding stops and no message is sent to

the central station. The keypad will display “CA” (Fixed-Word

display keypads) or “CANCELED ALARM” (Alpha display keypads).

If the system is not disarmed before the end of entry delay, and an

entry/exit or interior zone is still open, an “EXIT ALARM” message

will be sent to the central station if an Exit Error Report code is

entered. The keypad will display “EA” (Fixed-Word display keypads)

or “EXIT ALARM” (Alpha display keypads), and alarm sounding will

continue until the system is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs in an exit or

interior zone within 2 minutes following the end of the exit delay,

and an “EXIT ALARM” message will be sent to the central station.

With Contact ID format, the message will contain the zone number

and error code 374 (“ALARM–EXIT ERROR”).

*60

Trouble Report Code

0 = no report

1-F = see description above *59

This will be sent if a zone has a trouble condition.

UL: Required for UL commercial burglar alarm installations and

required for residential fire alarm installations.

*61

Bypass Report Code

0 = no report

1-F = see description above *59

This will be sent when a zone is manually bypassed.

UL: Required for UL commercial burglar alarm installations.

*62

AC Loss Report Code

0 = no report

1-F = see description above *59

Timing of this report is random with up to a 4-hour delay. If AC

restores before the report goes out, there is no “AC RESTORE”

report.

UL: Required for UL commercial burglar alarm installations and

required for residential fire alarm installations.

*63

Low Bat Report Code

0 = no report

1-F = see description above *59

Sent when a low-battery condition exists in the system’s battery.

UL: Required for UL commercial burglar alarm installations and

required for residential fire alarm installations.

*64

Test Report Code

0 = no report

1-F = see description above *59

† NOTE:

Make sure the Real-Time Clock

is set to the proper time

before

entering

the test report schedule command to

ensure that test reports are sent when

expected. (see Setting the Real-Time

Clock section on page 12-3)

Sent periodically to test that the communicator and phone lines are

operational.

Frequency of report is set in Scheduling mode

(event 11) or by the following key commands:

installer code + [#] + 0 + 0

= test report sent every 24 hrs

installer code + [#] + 0 + 1

= test report sent once per week

installer code + [#] + 0 + 2

= test report sent every 28 days

Each of these modes sets schedule 32 (VISTA-20P) or 8

(VISTA-15P) to the stated repeat option; first test report sent

12 hours after command

†

UL: Required for UL commercial burglar alarm installations and

required for residential fire alarm installations.

*65

Open Report Code

0 = no report

1-F = see description above *59

This is sent upon disarming of the system in the selected partitions.

UL: Required for UL commercial burglar alarm installations.

*66

Arm Away/Stay Report Code

0 = no report

1-F = see description above *59

This option allows for independent programming of Away and Stay

reports for each partition, including the common lobby.

NOTE:

“OPEN” reports are not sent if the associated closing report

is not enabled.

*67

RF Trans. Low Batt. Report Code

0 = no report

1-F = see description above *59

Sent when a wireless transmitter low-battery condition exists.

UL installations: must be enabled if wireless devices are used.

*68

Cancel Report Code

0 = no report

1-F = see description above *59

This is sent upon disarming of the system after an alarm condition

was reported.

*70

Alarm Restore Report Code

0 = no report

1-F = see description above *59

Sent when an alarm zone is restored to its non-faulted condition.

UL: Required for UL commercial burglar alarm installations and

required for residential fire alarm installations.

*71

Trouble Restore Report Code

0 = no report

1-F = see description above *59

This is sent when a trouble in a zone is restored

UL: Required for UL commercial burglar alarm installations.

4-5

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15