ADEMCO Accord Manual de instalación descargar pdf (Pagina 74)

Appendix D: Programming Summary

PROGRAMMING FORM

V1.46 PANELS

THE DEFAULT VALUES FOR EACH OPTION ARE SHOWN IN BRACKETS

DEFAULT MASTER CODE 1234 (User 1)

DEFAULT ENGINEER CODE 9090 (User 0)

To enter programme mode, enter your Engineer Code then #, then

(Power LED will flash, Spanner Flashes, Displays 00).

To exit programme mode press #, then

(Power LED on steady, Spanner/00 clears).

To programme each option, you must enter a Group N˚ then the option/zone N˚, then your selection, i.e., to programme zone 6 to be a

panic zone in the full set mode, enter 167. To put zone 3 on soak test, enter #231.

To view the programme in groups 1, 2, #2, 3, 4, 5, #6, 7 & 9, enter the Group N˚ followed by 00. Each group option will display in turn.

To view groups #1, 6, 8 & 0 enter Group N˚ followed by 0 then the N˚ of the option you want to view. The individual option will display.

ZONE PROGRAMMING

FOR FULL SET

GROUP ZONE ZONETYPE

1 1 (1)

1 2 (4)

1 3 (3)

1 4 (3)

1 5 (3)

1 6 (3)

1 7 (3)

1 8 (3)

ZONE PROGRAMMING

FOR NIGHT SET

GROUP ZONE ZONE TYPE

3 1 (1)

3 2 (1)

3 3 (3)

3 4 (3)

3 5 (3)

3 6 (3)

3 7 (3)

3 8 (3)

ZONE PROGRAMMING

FOR PART SET

GROUP ZONE ZONETYPE

2 1 (1)

2 2 (4)

2 3 (3)

2 4 (3)

2 5 (3)

2 6 (3)

2 7 (3)

2 8 (3)

ZONE TYPES

0 = NOT USED

1 = FINAL EXIT

2 = KEYSWITCH

3 = ALARM

4 = INTERMEDIATE EXIT

5 = TAMPER

6 = SILENT PA

7 = AUDIBLE PA

8 = EXIT TERMINATOR

9 = FIRE

GROUP

OPTION SELECTION

4 1=EXIT TIME (0=FINAL CONTACT/1-9 EXIT TIME X 10 SEC) (3)

4 2=ENTRY TIME (1-9 ENTR

Y TIME X 10 SEC) (3)

4 3=BELL CUT OFF TIME (SEE TABLE 1) (8)

4 4=PART SET EXIT W

ARNING (0=SILENT, 1=KEYPAD ONLY, 2=KEYPAD & SOUNDER) (0)

4 5=EXTERNAL BELLS & STROBE IN PART SET (0=NO, 1=YES) (1)

4 6=EXTERNAL BELLS & STROBE IN NIGHT SET (0=NO, 1=YES) (1)

4 7=TRIGGER OUTPUT

(SEE TABLE 2) (0)

4 8=EASY SET (#) (0=NO, 1=YES) (0)

4 9=PREVENT SET WITH FOLLOWING CONDITIONS (SEE T

ABLE 3) (0)

Table 1

BELL CUT OFF TIMES

0 = CONTINUOUS BELLS

1 = 1 MINUTE

2 = 2 MINUTES

3 = 3 MINUTES

4 = 4 MINUTES

5 = 5 MINUTES

6 = 10 MINUTES

7 = 15 MINUTES

8 = 20 MINUTES

9 = 30 MINUTES

Table 3

able 2

TRIGGER OUTPUT

0 = SET

1 = 0V DETECTOR RESET

2 = SET LATCH POSITIVE

3 = ALARM

PREVENT SET WITH FOLLOWING

CONDITIONS

0 = MAINS FAIL

1 = LOW BATTERY

2 = MAINS FAIL AND LOW

BATTERY

SYSTEM OPTIONS

GROUP OPTION SELECTION

5 1=AUDIBLE WARNING OF AC LOSS (0=NO, 1=YES) (0)

5 2=SUPPLEMENTAR

Y ENTRY (0=NO, 1=YES) (0)

5 3=ENGINEER RESET FOR ALARMS (SEE TABLE 4) (0)

5 4=HOTKEY ENABLE (0=NO, 1=YES) (0)

5 5=KEYPAD TAMPER LOCKOUT (0=NO, 1=YES) (0)

5 6=BELL OUTPUT (0 = NEG APPLIED, 1=NEG REMOVED) (0)

7=ALARM TRIGGER OUTPUT (0 = NEG APPLIED, 1 NEG REMOVED) (0)

5 8=ENGINEER RESET FOR DAY TAMPERS (SEE TABLE 4) (0)

5 9=ZONE CONFIGURATION (0=N/C LOOP

, 1=DOUBLE BALANCE,

2=E.O.L.) (0)

Table 4

ENGINEER RESET

0 = CUSTOMER

1 = ENGINEER

2 = TECHNISTORE

3 = ENGINEER &

TECHNIST

ORE

GROUP OPTION SELECTION

6 1=PRIMARY TELEPHONE NO. (20 DIGITS) (#=2 SEC PAUSE)

6 2=SECONDAR

Y TELEPHONE NO. (20 DIGITS) (#=2 SEC PAUSE)

6 3=ACCOUNT NO. (4 - 6 DIGITS)

6 4=USER 8 = DURESS CODE (0=NO, 1=YES) (0)

6 5=DOWNLOADER TELEPHONE NO. (20 DIGITS) (#=2 SEC PAUSE)

6 6=DOWNLOADER ID N˚ (8 DIGIT NUMBER, CANNOT BE VIEWED)

7=RING COUNT (00=NEVER ANSWER INCOMING CALLS

01-14=NUMBER OF RINGS, 15=ANSWER MACHINE DEFEAT) (14)

6 8=COMMUNICATOR FORMA

T (0=COMMUNICATOR OFF,

1=HIGH SPEED, 2=CONTACT ID) (1)

6 9=C/S RECEIVER HANDSHAKE OPTIONS (0=UK, 1=BELGIUM, 2=PARIS) (0)

RF ZONE PROGRAMMING

OVERRIDES HARDWIRE ZONES

GROUP ZONE SUPERVISION LOOP N˚. 7 DIGIT SERIAL NO.

#1 1

#1 2

#1 3

#1 4

#1 5

#1 6

#1 7

#1 8

ZONE SOAK TEST

ENABLE (14 DAY)

GROUP ZONE 1=ENABLE

#2 1 (0)

#2 2 (0)

#2 3 (0)

#2 4 (0)

#2 5 (0)

#2 6 (0)

#2 7 (0)

8 (0)

RF ZONE. PROGRAMMING

ENTER 9 DIGITS PER ZONE

IN SEQUENCE:

1=SUPERVISION 0=NO, 1=YES

2=LOOP N˚ 1=1, 2=2

3 -9=SERIAL N˚ 7 DIGITS

TO CLEAR RF

ZONE, TYPE 0, 0

FOR SUPERVISION & LOOP

1 2 ... 69 70 71 72 73 74 75 76 77 78

Comentarios a estos manuales

Sin comentarios

ADEMCO Accord Manual de instalación Pagina 74

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Accord