ADEMCO 5130XM Manual de instrucciones descargar pdf (Pagina 17)

CONTACT ID REPORTING

This is the only formal that can identify all 64

protection zones by their unique zone (Contact) ID

numbers, and provides a 1digit event qualifier and

3-digit, specifically defined event code. which

quickly identifies the condition behg reported.

Contact ID reports in DTMF (Dual Tone Multi-

Frequency @ 10 characters per second) and

responds to a 1400 Hz followed by 2300 Hz

handshake, and a 1400 Hz kisaoff. This format also

uses checksum instead of two message verification.

A complete report takes under 3 seconds.

ADVISORY

Ademco’e new Contect ID reporting Is

cspeble of uniquely reporting ●ll 64 zones

of Information,

●s well ●s openings end

closlngs tor ●ll 22 users, to centrel

●tations equipped with the Ademco 685

receiver

uelng

sottwere level 4.4 or

higher.

685 sottware Iovels beiow 4.4

cannot support Contact ID reporting. For

Information regarding updeting the 685

receiver,

contact

Ademco’s Technical

Support group ●t 1-800-645-7492.

W. PROGRAMMING THE SYSTEM

The system is shipped with a set of pre-

programmed values that are designed to meet the

needs of many installations. These can be changed

by the installer to suit specific needs if desired. In

addition,

four

sets

of pre-programmed

communicationdefault values can

also be loaded by

the installer, each set designeo for a specific

communicationformat. Thaae too can be changed to

suit the needs of a particular installation.

Changes to these pre-programmed values can be

programmed directly trom the keypad or from a

computer terminai using the 4130PC Downloading

software, an iBM compatiblecomputer

and a HAYES

1200 SMARTMODEM. The following paragraphs

describes how to ioad the various default

programming sets.

For instructions on making

changes to particular programming fields, or for

using downloading, refer to the Technical Reference

Manual.

For alpha Controls, Engli$h Language descriptionsof

the zones and a custom installer message (which

appears when the system is ready to arm) can be

programmed. Refer to the instructions in the

Technics/ Refensmw Manua/ for details. ‘

The programming fields are grouped into two sets

of addresses. The first set is

accessed as soon as

programming mode is entered. To access the

second set of addresses (indicated on the

programming form by a “1” in front of the 2-digit

fieid address), press ●94 while in programming

mode,

To return to the first

press ●99.

To program specific data fwlds,

2-digit fmid address, then make

The console will beep when

completely programmed and

set of addresses,

press ~] plus the

the required entry.

a field has been

will automatically

display the next data field in numeriial order.

To view the contents of a data field, press [#] plus

the 2-digit field address. The fields entries will be

displayed, but no changes to these entries can be

made.

There are five sets of pre-programmed defaults

available (one standard, plus four different

communicationdefaults). Any one of these can be

ioaded into the system’s memory by doing the

following:

1. Enter programming mode by pressing ~] and

[#] at the same time and within 30 seconds

after power is applied. OR Enter the installer

code, and press CODE + [0] +[0].

2. Load one of the default programming sets by

entering one of the followingcode sequences

IPRESS I TO LOAD THIS PROGRAMMING SET

“97 Loads standard defualt values.

“94”80

Standard Low Speed 3+114+1

I “94”811 Expanded Low Speed 3+1/4+1

“94”821 AdemcoHighSpead

●94*831

Expanded4+2

A complete list of the defautt values can be found in

the Technical Reference Manual.

To Exit programming mode, press either “98 or

“99.

Use ●98 to prevent re-access to

programming mode by installer code method. “99

allows installer code access to programming mode.

-15-

/’D3

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 25 26

Comentarios a estos manuales

Sin comentarios

ADEMCO 5130XM Manual de instrucciones Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 5130XM