ADEMCO 5130XM Manual de instrucciones descargar pdf (Pagina 10)

111. (B) SYSTEM CONFIGURATION (PERIPHERALS)

—

REMOTE CONSOLES —

GENERAL

Both the 4130XM and the 5130XM supply up to

280mA (200mA for UL certificated installations) of

auxiliary power for remote consoles and/or other

auxiliary devices such as motion detectors or 4-

wire smoke detectors. The 4140XM supplies up to

700mA for non-UL usage and up to 400mA for UL

applications. You must keep this in mind when

adding remote consoles so you dorm over-draw

current from the panel. This would result in a

battery which is never fully charged, or possibly a

blown auxiliary power fuse. Up to 7 remote

consoles can be used.

In the event you need more than the allowed number

of remote consoles, you can use a second 1350

power pack to power up to 7 extra 4137s/5137s.

Instead of

using the panef’s auxiliary power

connection to the red and black console lead,

connect the Positive (+) terminai of the 1350 to the

biue console fead, and the Negative (-) to the black

iead. As iong as AC power is present these extra

consoles are active. If AC is lost, the system’s

back-up battery will take over and oniy the

consoles powered from auxiliary power wiii be

active.

—

SMOKE DETECTOR

ZONE 1

When programmed as an EOLR supervisedFiRE zone

(type 09 in program field “02), up to three 2-wire

smoke detectors can be used. Recommended are the

BRK1 400 Ionization detector, 2400 Photoeiectnc

smoke detector, and the 2400TH Photoelectric

smoke detector with 135°F heat sensor.

ADVISORY

ifthe EOLRianot attheendofthe loop, the zoneis

not fully supervised. The system wiil not respond

to an open circuit within the zone.

ZONES 2 THROUGH 8

These zones can support as many 4-wire smoke

detectors as can be powered, when programmed as

a FIRE zone, type 09, in program fwld “02. There

are only two requirements: (1) The zones must be

configured for EOLR supervision, and (2) A

normally-closed,

momentary switch must be

inatalied in series with the power to the detectors

in order to allow reset of the smoke detectors after

an aiarm. The detectors must be wired in parallel,

with the EOLR at the last detector for fuil

supewision.

NOTE If using a 4140XM, make sure you power

at least one remote console from auxiliary power,

othenviee there wouid be no means of controlling

the panel duringan AC ioas.

4137

- For use with the 4130XM, 4140XM or 5130XM

Controls

- 60 mA current draw

- Power up to 7 consoles from the 4140XM.(non-UL)

5137

For use with the 4140XM or 5130XM Controls

-60 mA current draw standby

-90 mA current draw with backlighting

- Power up to 7 consoles from the 4140XM (non-UL)

CONFIGURATIONS —

POLLING LOOP SMOKE DETECTORS

(4192SD, 4192SDT or 4192CP)

Can be added to the 2-wire Poiling Loop via the

4152LMB ioop module, on zones 10 through 64 (as

programmed in fields “03, “04, “05, 1●O1,

1“02, 1’03, 1●O4 and 1“05).

These detectors

have a built-in RPM which is DIP switch

programmable. They are wired in paraliel to the

poiiing loop, and do not need auxiliary power or a

separate reset switch. The polling loop provides

power and reset signals to the detectors, as well as

alarm and trouble signals from the detectors. Refer

to the poiling loop wire run iength tabie in the

PoilingLoop Expansion3ection.

WIRELESS SMOKE DETECTOR

(5706)

Up to 8 smoke detectorscan be used and assignedto

zonea 48-55 as long as these zones are enabled for

RF usage and are programmed as Fire zones (type

09). A 4280 RF Receiver must be connected to the

poliing ioop to support the wireiess smoke

detectors. Refer to the instructions provided with

the 4280 for installation information.

-8-

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 25 26

Comentarios a estos manuales

Sin comentarios

ADEMCO 5130XM Manual de instrucciones Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 5130XM