ADEMCO 5130XM Manual de instrucciones descargar pdf (Pagina 15)

V. SYSTEM OPERATION

— SECURITY ACCESS CODES —

The VISTA XM System allows up to 22 security

The Installer also programs the master security

access codes

to be assigned, each identified by a code, which is the code intended for use by the

user ID numkr.

primary user of the system. The master code can

The installer programs an Installer’s Code initially

then be

used to assign up to twenty temporary

as part of the programming procedure, and this

codes, which can be used by secondary users of the

code is the only code that permits re-entry into the

system who do not have a need to know the master

programming mode (unless ●98 has been previously

code. In addition,the Quick Arm feature can also be

used to exit the programming mode, see below).

programmed, which enables the [#] key to be

The Installers Code can also be used to perform

pressed in lieu of entering the security oode when

normal system functions, but cannot assign

arming the system.

temporary cod6s.

As shipped from the factory, an initial Installer’s

The system also provides an Installer Code lock-out

coda and master code is pm-programmed, and can

feature, which prevents the use of the Installer’s

be changed by the installer to any code desired.

Code from re-accessing the Programming mode

The pre-programrned codes are as follows:

after the initial programming.

This feature is

activated by pressing ●98 to exit Programming

4130XM = 4-1-3-0 All Controls = 1-2-3-4

mode. The only way to access Programming mode

once this feature is activated, is by powering don

4140XM = 4-1-4-0

the system and powering up again, and then

5130XM = 5-1-3-O

pressing both the “

and # keys at- the same time

within 30 seconds of power up. If re-acceas to

For additional information about security codes,

Programming mode using the Installer’s Code is

refer to the

Technics/ Reterence Manual and/or the

desired after initial programming, then exit

User’s Manual.

Programming mode by pressing “99.

— RECALLING ALARM & TROUBLE MESSAGES —

The system’s alarm memory retains all eventa for

a period of 10 days, starting at the time of the

firat event. Upon expiration of the 1O-day period,

all history is automatically erased and the alarm

memory will reset. The next 10-day cycle will

begin when the next event occurs.

Recall by service personnel will display all events

that have occurred from the start of the 10-day

cycle to the time of recall. Note that Recall will end

any 10day cycte in progress. The LCD display on

the 4130XM/41 37 console will indicate the number

of the zone in which the event occurr”ed(e.g., 01,

02, etc.), accompanied by the word CHECK

(trouble), ALARM and, If applicable, FIRE, to

describe the type of event that occurred in the

displayed zone.

— KEYPAD

The keypad atlows the user to arm and disarm the

system, and perform other system functions, such

as bypassing zones, view messages from the

central station and display zone descriptors. Zone

and system conditions (alarm, trouble, bypass) are

displayed in the Display Wtndow.

If a 5130XfvV5137 is used, an alpha descriptor of

the zone will be displayed in addition to its zone

number. If more than one event had occurred, the

events will be displayed in numerical sequence.

Each disptay will appear for 1-2 seconds, then the

next event will be displayed. When all eventa have

been displayed, the displays are repeated.

To display

the 10-dey hletory, enter the

security code and press the O key.

To ●xit Recsll, enter the security code and

press the OFF key. All existing memory is erased

and the alarm memory is reset. The 10-day cycle

will start again only when the next event occurs.

FUNCTIONS —

For additional information, refer to the User’s

Manual.

EEl

-13-

Acy

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 25 26

Comentarios a estos manuales

Sin comentarios

ADEMCO 5130XM Manual de instrucciones Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 5130XM