ADEMCO Vista-128B PLUS Guia de preparacion descargar pdf (Pagina 38)

– 38 –

PROMPT

EXPLANATION

02 RELAY GROUP

Relays may be grouped for common activation by time-driven events (commands 06-10). Enter 00 (no

group) or 01-15 for a specific group number.

Press [✱] to continue.

02 RESTRICTION

1=YES 0=NO 0

The system may have some devices that are not intended to be under end user control, such as relays

activating fire doors or machinery. Enter 1 if the end user will be restricted from accessing this relay group.

Press [✱] to continue.

02 RELAY TYPE

V-PLEX 0

Enter 0 for V-Plex (polling loop) devices. Enter 1 for (ECP) relay modules (4204/4204CF). Enter 2 for X10

devices. Enter 3 for (FSA) Fire System Annunciator.

Press [✱] to continue.

02 V-PLEX ZONE #

000

For polling loop trigger outputs (4101SN), enter the protection zone number (001-250) linked to each output,

if used. Be sure to enroll the module’s serial number (see Zone Programming).

Press [✱] to continue.

02 ECP ADDRESS

If you selected 1 or 3 for (4204/4204CF or FSA), enter the actual module's address (01-15 – 4204/4204CF)

(08-23 – FSA) as set by its DIP switches. Up to 8 4204/4204CF modules and up to 4 FSA modules can be

installed in a system.

Press [✱] to continue.

02 MODULE RELAY#

For 4204 Relay Outputs, enter the specific relay number on that module (1-4). For 4204CF outputs,

enter

only module relay number 1 (Output A) or relay number 3 (Output B)

. These are the only two

programmable relays on the 4204CF Module.

Press [✱] to continue.

The keypad will display the Start and Stop summary screens again.

Press [✱] to continue.

02 HOUSE CODE

A 00

If you selected 2 for X-10 devices, enter the numerical equivalent of the House Code of the device, as

follows:

A=00 D=03 G=06 J=09 M=12 P=15

B=01 E=04 H=07 K=10 N=13

C=02 F=05 I=08 L=11 O=14

02 UNIT CODE

Enter the numerical unit code of the X-10 device (00-15).

Press [✱] to continue.

The keypad displays the Start and Stop summary screens again.

Press [✱] to continue.

01 LED #

Enter the LED number on the FSA module (01-08 for FSA-8; 01-24 for FSA-24).

Press [✱] to continue.

The keypad displays the Start and Stop summary screens again.

Press [✱] to continue.

When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt.

If you are defining a zone list, continue to the next section. If not, enter 00 + [✱] at the next two prompts. You will then be

asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter ✱99 to exit programming completely.

If supervision of the 4204CF Relay Output is desired, enter a response type for that output's corresponding supervisory zone.

This is equal to 600 + [Relay ID No.]. For example, if you are programming Relay ID No. 1, the relay's supervisory zone 601.

Program this zone with response type 05 (Day/Night) in

Zone Programming

Zone List Programming

After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone

list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:

PROMPT

EXPLANATION

ENTER Zn LIST ?

00=QUIT 00

Enter the zone list number 01-15. Enter 00 to quit.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Guia de preparacion Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS