ADEMCO Vista-128B PLUS Guia de preparacion descargar pdf (Pagina 17)

– 17 –

PROMPT

EXPLANATION

010 Silent ?

1 = YES 0 = NO 1

If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter 1 to enable. The zone

follows all the selected response type’s characteristics, except in the alarm condition, the alarm output and

the keypad sounder do not sound and the keypad does not display the alarm condition.

Enter 0 to disable.

Press [✱] to continue.

010 Bypass Group

01-15 01

If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter the bypass group for the

zone (01–15). This enables the user to bypass a group of zones by entering [User Code] + [6] (Bypass) +

[✱] + [Group No.] (01-15).

Enter 00 for None.

Press [✱] to continue.

010 ACCESS POINT

(00-31) 01

If response type 27, or 29 was selected, this prompt will be displayed. Enter the access point to be

controlled by the input type (00-31 for type 27; 01-15 for type 29).

Note: If you are using the VistaKey module, the access point must match the address that was set in the

module.

Press [✱] to continue.

010 ENTRY OR EXIT

If response type 27, or 29 was selected selected, this prompt will be displayed. Enter whether the access

point is an entry or exit point.

0 = entry; 1 = exit

Press [✱] to continue.

010 Panel ID#

(01-08) 01

If you selected response type 14, this prompt appears. Enter the panel ID#. This ID # must match the ID #

programmed in Device Programming.

Press [✱] to accept entry.

010 Partition

Enter the partition number (1–8) you are assigning this zone to.

Press [✱] to continue.

010 REPORT CODE

1st 03 2nd 12 3C

Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2

numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C."

(Refer to the

System Communication

section in the

Installation and Setup Guide

for more information about

report codes and reporting formats.)

Press [✱] to continue.

010 INPUT TYPE

RF Xmitter 3

Input types 4 & 5 are

valid for certain 5800

Series transmitters only

(e.g., 5801, 5802, 5802CP

& 5803).

If using input type 02

with a door/window type

transmitter, only loop 1

may be used.

Input type 10 is

applicable only if

PassPoint ACS is

installed with the VISTA

Gateway Module.

If you selected response

type 14, 28, or 29 the

input type MUST be 00.

Enter the input device type as follows:

00 = not used

01 = hardwired

02 = RF motion (RM type)

03 = supervised RF transmitter (RF type)

04 = unsupervised RF transmitter (UR type)

05 = RF button-type transmitter (BR type)

06 = serial number polling loop device (SL type)

07 = DIP switch-type polling loop device

08 = right loop of DIP switch type device

09 = keypad input (code + #73)

10 = PassPoint ACS input

11 = VistaKey Door Status Monitor (DM)

12 = VistaKey Request to Exit (RE)

13 = VistaKey General Purpose (GP)

Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278 PIR, which

allow hardwired devices to be monitored by the polling loop.

If you are programming hardwired or DIP switch polling loop devices, the summary display appears after

completing this entry.

NOTE: Input types 11 (DM), 12 (RE), and 13 (GP) should only be used with VistaKey modules.

Press [✱] to continue.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Guia de preparacion Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS