ADEMCO Vista-128B PLUS Guia de preparacion descargar pdf (Pagina 22)

– 22 –

PROMPT

EXPLANATION

XMIT TO CONFIRM

PRESS ✱TO SKIP

The prompt to confirm appears. This prompt only appears if you answered “Yes” at the “SET TO

CONFIRM?” prompt.

The system enters a confirmation mode so that the operation of the actual programmed input can be

confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you

may press the [✱] key on the keypad to save the serial and loop number combination without confirming.

Entd A022-4063 1

Rcvd A022-4064

If the serial number transmitted does not match the serial number entered, a display similar to the one

at the left appears. If the loop number does not match, it also is displayed.

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary

display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct

serial number.

Activate the button on the wireless key again after re-entering the serial number.

Zn ZT P RC In L

011 00 1 10 00 1

If the serial number transmitted matches the serial number entered, the system beeps 3 times and

advances to the summary display for the next zone's programming.

After all the zones have been programmed, enter 000 for the zone number to quit.

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in

the appropriate column on the worksheets provided later in this

Programming Guide

; then enter the other information

(zone number, zone type, etc.) relevant to that device.

Entering Wireless Keys

If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:

PROMPT

EXPLANATION

FROM TEMPLATE

1–6 1

Enter template number (1–6).

1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart

that follows these procedures.

Select from templates. Press [✱] to display template (template 1 shown selected).

Note: If necessary, press [#] to back up and re-enter template number.

Press [#] if you want to return to zone attributes screen.

L 01 02 03 04

ZT 23 22 21 23 1

When you press [✱], the selected template is displayed.

Top line of display represents loop numbers; bottom line represents zone type.

Press [✱] to accept template.

PARTITION

Enter partition number for wireless key.

Press [✱] to continue.

ENTER ZONE NO

000 = QUIT 024

▲

Example of zone number

suggested by the system.

This indicates that zones

24, 25, 26, and 27 are

available.

The system searches for the highest available, consecutive 4-zone group (the four zones required for the

5804 and 5804BD), and displays the lowest zone number of the group.

If you want to start at a different zone number, enter the zone desired and press [✱].

If that zone number is displayed, the system has the required number of consecutive zones available,

beginning with the zone you entered. If not, the system again displays a suggested zone that can be used.

If the required number of consecutive zones is not available at all, the system will display “000.”

Press [✱] to accept.

024 INPUT S/N L

AXXX-XXXX 1

To enter the serial number:

Press and release a button on the wireless key.

Manually enter the 7-digit serial number printed on the device’s label.

Press [✱] to accept serial number. The system checks for a duplicate.

If a duplicate exists, a long error beep will sound and the serial number reverts back to all “X”s allowing

you to re-enter the serial number.

Use the [A] key to move forward within the screen, and the [B] key to back up.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Guia de preparacion Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS