ADEMCO Vista-128B PLUS Guia de preparacion descargar pdf (Pagina 37)

– 37 –

Choices for Start/Stop Zone Types and System Operations:

00 = No Response (Not Used) 23 = No Alarm Response 41 = AC Power Fail

01 = Entry/Exit #1 42 = System Battery Low

02 = Entry/exit #2 43 = Communication failure

03 = Perimeter

27 = Access Point (allows more than one

relay to be controlled by activation if

access point request)

44 = RF Low Battery

04 = Interior Follower 28 = MLB Supervision 45 = Polling Loop Failure

05 = Trouble Day/Alarm Night 29 = Momentary Exit 47 = Console Failure

06 = 24-Hr. Silent 31 = End of Exit Time 51 = RF Receiver Failure

07 = 24-Hr. Audible 32 = Start of Entry Time 52 = Kissoff

08 = 24-Hr. Auxiliary 33 = Any Burglary Alarm 54 = Fire Zone Reset

09 = Fire Alarm or Trouble 34 = Code + [#] + 71 Key Entry 55 = Disarm + 1 Minute

10 = Interior W/Delay 35 = Code + [#] + 72 Key Entry 56 = XX Minutes (enter XX in field 1*74) *

14 = PLM Supervision 36 = At Bell Timeout ** 57 = YY Seconds (enter YY in field 1*75) *

16 = Fire With Verification 37 = 2 Times Bell Timeout ** 58 = Duress

20 = Arming-STAY*** 38 = Chime

21 = Arming-AWAY**** 39 = Fire Alarm

22 = Disarming (Code + Off) 40 = Bypassing

60 = Audio Alarm Verification (must be

selected for both START and STOP

operation)

* Stop condition only

** Or at disarming, whichever occurs earlier

*** The output also activates when the partition is armed in the INSTANT mode

**** The output also activates when the partition is armed in the MAXIMUM mode

If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74

and 1*75 for the respective relay timeouts for minutes and seconds.

PROMPT

EXPLANATION

02 START: ACS PT

(00-31) 00

If the start zone type you selected was 27 (access point), this prompt is displayed. Enter the access point

(00-31) that will start the relay action.

Press [✱] to continue.

02 START: PARTN

ANY PARTITION 0

If the starting event will be limited to occurring on a specific partition, enter the partition number (1-8) in

which the start event will occur. Enter 0 for any partition.

Press [✱] to continue.

Do not use a zone programmed with an RF Button (Input Type BR) to STOP a relay. The system will not de-

activate the relay.

PROMPT

EXPLANATION

02 STOP: ZN LIST

If a zone list is being used to stop this relay action, enter the zone list number, 1-15. The restore of a zone

on the zone list stops the relay. If a zone list is not being used, enter 0.

Press [✱] to continue.

02 STOP: ZN TYPE

NO RESPONSE 00

If a Zone Type/System Operation is being used to stop the relay action, enter the 2-digit code listed in the

Choices for Start/Stop System Operation chart.

Press [✱] to continue.

02 STOP: ACS PT

(00-31) 00

If the stop zone type you selected was 27 (access point), this prompt is displayed. Enter the access point

(00-31) which will stop the relay action.

Press [✱] to continue.

02 STOP: PARTN

ANY PARTITION 0

This is the partition to which the stop condition will be limited. Enter 0 for any partition. Enter 1-8 for specific

partition number.

Press [✱] to continue.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Guia de preparacion Pagina 37

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS