ADEMCO 4120XM Guía de usuario descargar pdf (Pagina 57)

Programming Zone

General

Entering Zone

Descriptions

If using an Alpha console, a user-friendly English language description/location of

all protection zones, keypad panics, and 4281 supervision faults can be

programmed into the system. Each description can be composed of a

combination of words (up to a maximum of 3) that are selected from a vocabulary

of approximately 220 words stored in memory, and any word can have an “s”or”

‘s “ added

to it. In addition, up to 20 installer-defined words can be added to

those already in memory. Thus, when an alarm or trouble occurs in a zone, an

appropriate description for the location of that zone will be displayed at the

console. An installer’s message can also be programmed which will be displayed

when the system is “Ready” (ex. THE PETERSON’s).

Note: Alpha descriptor entry can be accomplished locally at the Alpha console or

remotely using a4130PC

Downloader.

1. Enter programming mode as described previously.

2. Key ●93. The following will be displayed:

● ZN ??

In this mode, the console keys have these functions:

[3]

[1]

[2]

[6]

[8]

[#]

NOTE: When programming descriptors for zones 95-99 (panics), the following

numbers

must be entered in place of the corresponding zone number.

Scrolls both alphabet and actual words in ascending alphabetical order.

Scrolls both alphabet and actual words in descending alphabetical order.

Adds or removes an “s” or”’s” to a vocabulary word.

Toggles between alphabet and actual word list, and used to accept

desired entries.

Saves the zone description in the system’s memory.

# plus zone number will display the description for that zone.

ZONE PANIC

PANIC ENTER

NUMBER KEY PAIR

SINGLE KEY

NUMBER

95 1+*

A 94

3+#

*+#

B 96

Key

●O1to begin entering the description for zone 1, (key ●O2for zone 2, *O3

for zone 3 etc.). The following will be displayed:

● ZN 01 A

Note that the first letter of the alphabet appears after the zone number, and

that the zone number is automatically included with the proposed description.

Select the first letter of the desired description (note that “A= is already

displayed). Use key [3] to advance through the alphabet and key [1] to go

backward. For example, assume the desired description for zone 1 is BACK

DOOR. Press key [3] repeatedly (or hold down the key) until “B” appears, then

press key [6]. to display the first available word beginning with B. Repeatedly

press key

[3] to advance through the available words until the word BACK is

displayed. Press key [1] to move backward through the word list.

To add an “s” or” ‘s”, press the [2] key. The first depression adds an “s”, the

second depression adds an “ *s “,

the third depression displays no character

(to erase the character), the fourth depression adds an “s”, etc.

To accept the chosen word, press the [6] key, which toggles back to the

alphabet list.

For selection of the next word (DOOR), repeat step 4, but press key [3] until

the desired first letter of the next word appears (in this example, “D”). Then

press key [6] to display the first available word beginning with “D”. Press key

[3] repeatedly until the desired word (DOOR) appears. To accept the word,

press the [6] key, which again toggles back to the alphabet list.

When all desired words have been entered, press key [8] to store the

description in memory.

To review the zone descriptions, key [#]

plus zone number (e.g., #01). To edit

zone descriptions, key [x] plus zone number (e.g.,

●O1)

To exit the zone description mode, key

●99.

-57-

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 79 80

Comentarios a estos manuales

Sin comentarios

ADEMCO 4120XM Guía de usuario Pagina 57

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4120XM