ADEMCO 4120XM Guía de usuario Pagina 27
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
POWERING THE SYSTEM
Primary Power
Back-Up Power
Earth Ground
Connections
Power-Up Procedure
Power to the Control panel is supplied by model No. 1321/TF2* Plug-in
Transformer which is rated at 16.5VAC, 25VA. Caution must be taken when
wiring this transformer to the panel to guard against blowing the fuse inside the
transformer (non-replaceable).
● NOTE: Use 1321CN Transformer in Canadian installations.
In
the event of an AC power loss, the Control panel is supported by a back-up,
rechargeable gel cell battery. YUASA NP4-12 (12V, 4AH*) and NP7-12 (12V,
7AH) batteries are recommended.
Do not use Gates batteries (sealed lead-
acid type).
● Use 4AH battery for UL installations.
The standby battery is automatically tested every 24 hours, beginning 24 hours
after exiting programming mode. In addition, entry into the test mode will cause a
battery test to be initiated.
BATTERY STANDBY TABLE
AUX. STANDBY CURRENT DRAW
NOTE: These figures are approximate, and
AMP-HRS. 400mA
700mA mayvary dependinguponthe age, quality,
4.0”
10 hrs.
5.7 hrs.
and capacity of the battery at the time of the
7.0
15 hrs.
8.5 hrs.
AC
10SS.
● Use 4AHbatteryfor ULinstallations
In order for the lightning transient protective devices in this product to be
effective, the designated earth ground terminal, must be terminated in a good
earth ground. The following are examples of good earth grounds available at
most installations:
Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is
recommended) firmly secured to the pipe to which the ground lead is electrically
connected and secured.
AC Power Outlet Ground: Available from 3-prong, 120VAC, power outlets only.
To test the integrity of the ground terminal, use a three-wire circuit tester with
neon lamp indicators, such as the UL-Listed Ideal Model 61-035, or equivalent,
available at most electrical supply stores.
1.
2.
3.
4.
5.
Fill out the AUXILIARY DEVICE CURRENT DRAW WORKSHEET (TABLE 1)
provided on the next page. Make sure that the total current drawn by all
devices from the Auxiliary output does not exceed its rating of
700 mA (400
mA for UL).
CAUTION: Failure to observe the auxiliary output current rating will result in a
battery which does not charge properly or possibly a tripped circuit
breaker.
Wire the transformer to terminals 1 and 2 on the control (before connecting the
battery) as shown in the SUMMARY OF CONNECTIONS diagram. Do not
plug in the transformer at this time.
Connect all auxiliary devices, such as consoles, zone expanders, RF
receivers, PIRs, etc.
Plug the transformer into a 24-hour, uninterrupted 120VAC outlet. After a few
seconds, the green “POWER” LED* on the console(s) should light and the
console(s) should display “READY” (Fixed-word consoles) or
“DISARMED.,..READY TO ARM” (Alpha consoles).
● Some consoles are equipped with a “READY” LED in place of a “POWER”LED.
Connect the battery to the battery connector tabs on the PC board (observing
correct polarity), as shown in the SUMMARY OF CONNECTIONS diagram.
-27-
- INSTALLATION 1
- INSTRUCTIONS 1
- I%U)EMCOI 1
- CONGRATUMTIONS! 3
- LIST OF ILLUSTRATIONS 6
- SUMMARY OF SYSTEM FEATURES 7
- BASIC 8 HARD-WIRED ZONES 10
- Zones 2-8 11
- TS2 HEAOER 12
- 4219 Zone Expander ● 13
- GeneraI Information 14
- /w%k%’wrO 15
- Wireless Zone Types 17
- Receiver Fault 18
- Annunciation 18
- 00000000 20
- ----- 21
- REMOTE CONSOLES 22
- I I~1 /l 23
- EXTERNAL SOUNDERS 24
- PHONE CONNECTIONS 24
- Ground Start Module 25
- OFSOAROlNSERTEO 26
- SIOEVIEW 26
- POWERING THE SYSTEM 27
- ❑ & ❑ (12V + and -) 28
- ❑ , 12V+ & Ground Return) 28
- SECURITY ACCESS CODES 29
- Assigning or 30
- Deleting Temporary 30
- Codes By User 2 30
- (Master User) 30
- CONSOLE KEYPAD FUNCTIONS 31
- [*I+ [W I B 32
- TROUBLE CONDITIONS 33
- Other Trouble 34
- Conditions 34
- Power Failure 34
- Split/Duai Reporting 35
- Ademco Low Speed 35
- Sescoa/Radionics 35
- 4+2 Reporting 35
- 4+2 Express 36
- Ademco High Speed 36
- Reporting 36
- No effect 38
- Programming Procedures 39
- Programming Steps 40
- Easy-To-Program 41
- Communication 41
- 010 BYPSSRst 43
- EIIEHIIE mHIIlsta*fd 44
- Klmmlmmtml 46
- (Q=no/l=yes) 48
- (Q/1 /2f3) 50
- (00;01-15) 53
- 1.34 communication 55
- Programming Zone 57
- Adding Custom 58
- Creating A Custom 58
- Message Display 58
- How Does 60
- Downloading Work? 60
- What Can Be Done 61
- Panel IS ● Bypass a Zone 61
- How Secure Is 61
- RED BLUE WHITE 62
- Using The Test 63
- Turning The System 64
- Over To The User 64
- Remote Consoles 65
- Hard-Wired Zones, 1-8 65
- Wireless 66
- Communications 67
- X 4.75”H X 1.25” D 69
- (DOC) STATEMENT 73
- ADEMCO LIMITED WARRANTY 75
- N6493V1 10/93 76
- 4120XM PROORAMM8NQ FORM 77
- ❑ clclclclclclcl 78
- ❑ 0000000 78
- ❑ lmnclclcl 78
- ❑ lnciclnclcn 79
- DISABLETROUSLESOUNDERFORRF 80
- DivisionOf PittWytirf.watia’t 80
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4120XM
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-20HW Guía para resolver problemas
(100 paginas)
(100 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE Manual de usuario
(24 paginas)
(24 paginas)
(56 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales