ADEMCO VISTA-15PSIA Especificaciones descargar pdf (Pagina 47)

– 47 –

WORKSHEET for SCHEDULES

(installer code + [#] + [6] [4]; master code can only access schedules 01-16 for VISTA-20P, 01-04 for VISTA-15P, and events 00-07 for both

controls; VISTA-15P supports up to 8 schedules, VISTA-20P supports up to 32 schedules )

No. Event Device No. Group No. Partition Start Time/ Stop Time/ Repeat Random

(see list below) for “01” events: for “02” events: for “04-06” events: Days Days (1-4) (yes/no)

enter 01-18 enter 1-8 enter 1, 2, or 3

(VISTA-20P)

Events: Master/Installer Installer Only

00 = clear event 03 = latch key report 06 = auto disarm 10 = display custom words 8-10

01 = device on/off 04 = forced STAY arm 07 = display “reminder” 11 = periodic test report

02 = user access 05 = forced AWAY arm

Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week

TABLE OF DEVICE ADDRESSES

This Device Uses Address Reports as †† Enabled By…

RF Receiver 00 100

∗56 zone programming: input device type entry

AUI 1 (touchscreen) 01 n/a

automatic if AUI enable field ∗189 enabled for AUI 1

AUI 2 (touchscreen) 02 n/a

automatic if AUI enable field ∗189 enabled for AUI 2

AUI 3 (touchscreen) (V20P) 05 n/a

automatic if AUI enable field ∗189 enabled for AUI 3

AUI 4 (touchscreen) (V20P) 06 n/a

automatic if AUI enable field ∗189 enabled for AUI 4

Communications Device (LRR) 03 103

automatic if communications device enabled in menu mode ∗29

4286 Voice Module 04 104

automatic if phone module access code field ∗28 enabled

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 (for zones 33 - 40)

module 5 (for zones 41 - 48)

(V20P)

107

108

109

110

111

∗56 zone programming: input device type entry, then:

automatic if zone no. 9-16 entered as AW type or relay assigned

automatic if zone no. 17-24 entered as AW type or relay assigned

automatic if zone no. 25-32 entered as AW type or relay assigned

automatic if zone no. 33-40 entered as AW type or relay assigned

automatic if zone no. 41-48 entered as AW type or relay assigned

Relay Modules (4204):

module 1

module 2

module 3

module 4

(V20P)

112

113

114

115

∗79 output device programming: device address prompt:

entered at device address prompt

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

n/a

data field programming as listed below:

always enabled, all sounds enabled.

data field ∗190

data field ∗191

data field ∗192

data field ∗193

data field ∗194

data field ∗195

data field ∗196

RIS Communication 25 n/a

automatic if Remote Interactive Services enabled in field ∗91

5800TM Module 28 n/a automatic

†† Addressable devices are identified by “1” plus the

device address when reporting. Enter report code for

zone 91 to enable device reporting (default = enabled).

See field

∗199 for addressable device (ECP) 3-digit/2-

digit identification keypad display options.

AUI devices are not supervised and therefore do not

report.

1 2 ... 42 43 44 45 46 47 48

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-15PSIA Especificaciones Pagina 47

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-15PSIA