ADEMCO VISTA-15PSIA Especificaciones descargar pdf (Pagina 38)

– 38 –

SYSTEM SECURITY CODES

The systems provides one Installer code, one System Master code, plus a set of other user codes intended for other users of

the system. These codes can each be assigned one of 5 authority levels, which determine the functions each code can

perform as listed in the table below.

VISTA-20P: Provides 48 security codes (plus Installer code), including one System Master code, two Partition Master

codes, and 45 general user codes.

VISTA-15P: Provides 32 security codes (plus Installer code), including one System Master code and 31 general user codes.

Authority Levels (can be assigned to users 03-49 only; users 1 and 2 cannot be changed)

Level User No. Functions

Installer 01 (default=4112) perform all security functions except can disarm only if used to arm; can

enter program mode; can change System Master code; cannot assign any other user codes

NOTE: For security purposes, the factory default installer code should be changed.

System Master 02 (default 1234) only one system master code per system; can perform all security functions,

add/delete users in either partition, change system master code, view event log, set s

stem

clock, program keypad macro, program scheduled events, activate output devices

(triggers/relays)

Partition Master

(default)

P1 = 03

P2 = 33

VISTA-20P. Same as Master, except add/delete users limited to assigned partition only,

(these users can be assigned different authority levels, if desired; any user can be

assigned the partition master authority level)

0-User 03-49 (V20P)

03-33 (V15P)

perform securit

functions (arm, disarm, etc.) onl

; cannot add/delete users, view event lo

set system clock or program scheduled events

1-Arm Only see “user” arm system only

2-Guest see “user” can disarm the system only if it was used to arm the system

3-Duress see “user” performs security functions, but also silently sends a duress message to the central station;

reports as duress code user number.

4-Partition Master see “user” VISTA-20P. See Partition Master paragraph above; used to assign other user numbers as

partition masters

Refer to the user guide for detailed procedures on adding/deleting security codes and changing user attributes.

The following is a brief description of how to add user codes.

Changing the System Master code:

Using Installer code: Installer code + [8] + 02 + new code

Using current System Master code: System Master code + [8] + 02 + new code + new code again

Adding a User Code: Master code + [8] + 2-digit user no. + user’s code

Deleting a User Code: Master code + [8] + 2-digit user no. + [#] [0]

Assigning Attributes: Master code + [8] + 2-digit user no. + [#] [attribute no.] + value

Attributes: Values

1 = Authority Level 0-4 (see Authority Level table above)

2 = Access Group 0-8 (0 = not assigned to a group)

3 = Active Partition(s) 1, 2, 3 (common)

for this user; Enter partitions consecutively if more than one and press [#] to end the entries.

4 = RF Zone No. Assigns user number to button type zone for arm/disarm (keyfob must be

enrolled in system first; see Wireless Key Templates section).

Deactivating a key fob: You can deactivate the arming/disarming functions for a

key fob (ex. if lost or stolen) by deleting the associated key fob user. See “Delete

a User” above. Other key fob functions such as panic or device activation (if

programmed) remain active. To fully remove the programming for a key fob,

delete the zone(s) associated with the key fob functions.

IMPORTANT SECURITY NOTICE

Please inform the User about the security importance of their key fob, and what to

do if it is lost.

Explain that the key fob is similar to their keys or access card. If lost or stolen,

another person can compromise their security system. They should immediately

notify the Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then

remove the key fob programming from the security system.

5 = Open/Close Paging 1 for yes, 0 for no

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 47 48

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-15PSIA Especificaciones Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-15PSIA