ADEMCO VISTA-15PSIA Especificaciones descargar pdf (Pagina 25)

– 25 –

OUTPUT DEVICE PROGRAMMING GENERAL INFORMATION (*79/*80 Menu Mode)

Output Devices: The VISTA-20P system supports up to 16 relays and/or Powerline Carrier devices (X-10 devices)

plus 2 built-in trigger outputs in any combination. These 18 “outputs” are assigned to system-wide

output numbers (01-18). Use *79 Menu Mode to assign output numbers and map them to device

addresses.

The VISTA-15P supports 8 relays and 2 built-in trigger outputs (total 10 outputs).

Output Functions: The system also provides installer-defined output functions, which can be assigned to any of the

physical outputs. Therefore, the action of any one of the outputs can be based on as many of these

defined functions as desired. This lets a single relay or X-10 device perform many functions.

The control supports: V20P = up to 48 defined functions; V15P = up to 24 functions

Use *80 Menu Mode to define output functions.

WARNING: Relays and output devices are not recommended for life safety applications.

NOTE: When navigating the *79 and *80 menus: The [

✱

] key is used to accept an entry and advance to the

next prompt. The [#] key is used to revert back to the last question to check or change an entry. Press [

✱

] to

go forward again.

Programming Output Devices

1. Use *79 Menu Mode to assign module and output numbers and map them to device addresses.

NOTE: You must map output devices using *79 Menu Mode before you can use *80 menu Mode.

2. Use *80 Menu Mode to create output definitions, which control the output devices, if desired.

3. Use *81 Zone List Menu mode to define zone lists for use with output devices if the device action is based on more than

one zone.

• To program a device for manual activation (user code + [#] [7] / [#] [8] + 2-digit device number) or for scheduled automatic

activation, simply map the device using *79 Menu mode.

• To program a device to automatically activate upon a system event (or function key), use *79 Menu mode to map the device,

then use *80 Menu mode to define the automated device action.

∗

∗∗

∗79 RELAY/POWERLINE CARRIER DEVICE (X-10) PROGRAMMING MENU MODE

(press

∗

∗∗

∗

79 while in Programming mode) The *79 Device Mapping Worksheet is on page 45.

Use this menu to assign Relay Module device addresses and specific relay numbers, and Powerline Carrier unit numbers. The

system is based on predefined module addresses for 4204 and 4229 modules. Refer to the table shown at the “Module

Address” prompt on the next page and set the modules’ addresses (via module DIP switches) accordingly.

The following table shows how these outputs are identified.

Output Identification

This output… is identified by…

Relays the Relay Module’s device address and the relay position on that module (i.e. the physical relay

number, 1-4, on that module).

X-10 Device a house ID (entered in data field *27) and the unit number of the device.

Built-in Outputs the output number assigned, 17 for Trigger 1 and/or 18 for Trigger 2.

ENTER OUTPUT NO.

00 = QUIT xx

Device Output Number

VISTA-20P:

01-16 = relays/X-10

17, 18 = on-board triggers

VISTA-15P:

01-08 = relays/X-10

17, 18 = on-board triggers

[∗] to continue

00 to quit

This is the logical (or reference) relay number as used in the

system. Relays and X-10 devices are numbered 01-16; the on-

board triggers are numbered 17 and 18 and can be programmed

for inverted output, if required.

17 OUT NORM LOW

0 = NO 1 = YES 0

Output Normally Low

0 = no (standard default)

1 = yes

[∗] to continue

(prompt appears only if trigger 17 or 18 was selected above)

Selecting 0 (no) sets the output level normally high (default

setting).

Selecting 1 (yes) sets the output normally low.

Output Trigger 17 can be used for resetting 4-wire smoke

detectors

†

by connecting it to the negative power terminal of the

smoke detector, selecting 1 at this prompt, and setting as zone

type 54, fire zone reset, in *80 Menu mode.

After entry, display returns to Output Number prompt. Use *80

Menu mode to program the function of the trigger.

† Power Reset: This control does not automatically reset power

to 4-wire smoke detector zones, so you must use a relay (e.g.,

4204, 4229) or on-board trigger to reset power (also required

for fire verification).

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 47 48

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-15PSIA Especificaciones Pagina 25

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-15PSIA