ADEMCO VISTA-15PSIA Especificaciones descargar pdf (Pagina 4)

– 4 –

PROGRAMMING MODE COMMANDS

Compatibility: This document applies to systems with microprocessor version 9.1 or higher.

TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control):

A. POWER UP, then press [

✱

] and [#] at the same time, within 50 seconds of powering up (this method must be used if

✱

was used to exit program mode). OR

B. Enter Installer Code (4112) then 8 0 0.

PROGRAMMING COMMANDS

Task Command/Explanation

Go to a Data Field

Press [∗

∗∗

∗] + [Field Number], followed by the required entry.

Entering Data

When the desired field number appears, simply make the required entry. When the last entry

for a field is entered, the keypad beeps three times and automatically displays the next data

field in sequence. If the number of digits that you need to enter in a data field is less than the

maximum digits available (for example, the phone number fields *41, *42), enter the desired

data, then press [∗ ] to end the entry. The next data field number is displayed.

Review a Data Field Press [#] + [Field Number].

Data will be displayed for that field number. No changes will be accepted in this mode.

Deleting an Entry

Press [∗

∗∗

∗] + [Field Number] + [∗

∗∗

∗]. (Applies only to fields ∗40 thru *46, *94, and pager fields)

Initialize Download ID

Press ∗

∗∗

∗96. Initializes download ID and subscriber account number.

Reset Factory Defaults

Press ∗

∗∗

∗97. Sets all data fields to original factory default values.

Zone Programming

Press ∗

∗∗

∗56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800

RF transmitters.

Function Key Programming

Press ∗

∗∗

∗57. Unlabeled keypad keys (known as ABCD keys) for special functions

Zone Programming

(Expert Mode)

Press ∗

∗∗

∗58. Same options as *56 mode, but with fewer prompts. Intended for those familiar

with this type of programming, otherwise *56 mode is recommended.

Output Device Mapping

Press ∗

∗∗

∗79. Assign module addresses and map individual relays/powerline carrier devices

Output Programming

Press ∗

∗∗

∗80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers

Zone List Programming

Press ∗

∗∗

∗81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.

Alpha Programming

Press ∗

∗∗

∗82. Zone alpha descriptors

IP/GSM Programming

Press ∗

∗∗

∗29. For programming the IP/GSM options.

Exit Program Mode with

installer code lockout

Press ∗

∗∗

∗98. Exits programming mode and prevents re-entry by: Installer Code + 8 0 0.

To reenter programming mode, the system must be powered down, then powered up. Then

use method A above. See field *88 for other *98 Program mode lockout options.

Exit Program Mode

Press ∗

∗∗

∗99. Exits program mode and allows re-entry by: Installer Code + 8 0 0 or method A

above.

Scheduling Mode Enter code + [#] + 64. Create schedules to automate various system functions.

Site-Initiated Download Installer code + [#] + 1 (perform while system is disarmed and in normal mode)

AVS QUICK PROGRAMMING COMMANDS (for AAV sessions using the AVS system)

For controls with the following firmware revision levels, these commands automatically configure the control for AVS

operation. VISTA-15P = version 6.0 or higher; VISTA-20P = version 7.0 or higher

• installer code + [#] + [0] + 3: enable AVS operation

• installer code + [#] + [0] + 4: enable AVS operation and enable panels sounds on the AVST speaker

• installer code + [#] + [0] + 5: remove all programming options set by [#] + [0] + 3 quick command

• installer code + [#] + [0] + 6: remove all programming options set by [#] + [0] + 4 quick command

Refer to the AVS SYSTEM ENABLE and QUICK PROGRAMMING COMMANDS section for details on the specific options

that are set with each command, depending on the control used.

To select the AAV session communication path (phone line/communication device), see field ∗55 Dynamic Signaling Priority.

To enable AAV operation, use ∗91 Options field (option 4).

TO ENABLE REMOTE SERVICES

1. Enable the Remote Interactive Services (RIS) option in

programming field ∗91 (entry 2).

2. Use programming field ∗189 to enable a remote services

emulated keypad address.

3. Use ∗29 Menu mode to enable the communication

device.

4. If using Total Connect 2.0, use AlarmNet Direct website

to program the communicator and enable TC2 services.

Be sure to “send” the programming data down to the

Communicator.

IMPORTANT: The Real-Time Clock must be set before

the end of the installation. See procedure in the Setting the

Real-Time Clock section of this manual.

SPECIAL PROGRAMMING MESSAGES

•

••

• OC = OPEN CIRCUIT (no communication between

Keypad and Control).

•

••

• EE or ENTRY ERROR = ERROR (invalid field number

entered; re-enter valid field number).

•

••

• After powering up, AC, dI (disabled) or “Busy Standby

vx.x (firmware revision) Dl will be displayed after

approximately 4 seconds. This will revert to a “Ready”

message in approximately 1 minute, which allows PIRS,

etc. to stabilize.

You can bypass this delay by pressing [#] + [0].

NOTE for CANADIAN PANELS: Power up time is 2

minutes, and Contact ID report code 305 System Reset

is sent if the [#] + [0] command is not performed before

the 2 minutes expires.

•

••

• If E4 or E8 appears, more zones than the expansion

units can handle have been programmed. The display

will clear after you correct the programming.

1 2 3 4 5 6 7 8 9 ... 47 48

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-15PSIA Especificaciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-15PSIA