ADEMCO VISTA-48D Especificaciones descargar pdf (Pagina 51)

5-9

Start Output Device Mapping by pressing *79 while in Data Programming Mode. The following

prompts are displayed:

∗

∗∗

∗79 Menu Mode

PROMPT

VALID ENTRIES EXPLANATION

ENTER OUTPUT NO.

00 = QUIT xx

Device Output Number

01-18 = relays/X-10

[∗] to continue

This is the logical (or reference) relay number as used in the system.

Relays and X-10 devices are numbered 01-16; the on-board triggers

are numbered 17 and 18 and can be programmed for inverted output.

Use the worksheet on the Programming Form (printed separately) to

organize device numbers.

17 OUT NORM LOW

0 = NO 1 = YES 0

Output Normally Low

0 = no (standard default)

1 = yes

[∗] to continue

This prompt appears only for triggers 17 and 18.

Selecting 0 (no) sets the output level normally high.

Selecting 1 (yes) sets the output normally low.

Output trigger 17 can be used for resetting 4-wire smoke detectors by

connecting it to the negative power terminal of the smoke detector,

selecting 1 at this prompt, and setting as zone type 54, fire zone reset,

in *80 Menu mode.

After entry, display returns to Output Number prompt. Use *80

Menu mode to program the function of the trigger.

XX OUTPUT TYPE

DELETE 0

Output Type

0 = delete

1 = relay on 4204/4229 module

or 6164 keypad

2 = Powerline Carrier device

[∗] to continue

Select whether this is a relay or a Powerline Carrier (X-10) device.

If relay is selected, skip to “B” prompt.

If X-10 is selected, go to “A” prompt.

“A”

XX UNIT No.

Unit Number

01-16 = predefined address

[∗] to continue

If X-10 is selected, a prompt for the unit number appears.

Enter the unit code (set at the device) and press [∗].

The system returns to the Output Number prompt.

“B”

XX MODULE ADDR

07-15 yy

Module Address

07-15 = predefined address

[∗] to continue

If relay is selected, this prompt appears.

Enter the predefined address for this module as listed below. Make

sure the module’s DIP switches are set to the selected address (6164

keypad address is entered via its keypad programming prompts).

Module Addresses

Address Module or Keypad

07 1st 4229 (with zones 09-16) or 1st 6164

08 2nd 4229 (with zones 17-24) or 2nd 6164

09 3rd 4229 (with zones 25-32) or 3rd 6164

10 4th 4229 (with zones 33-40) or 4th 6164

11 5th 4229 (with zones 41-48) or 5th 6164

12 1st 4204

13 2nd 4204

14 3rd 4204

15 4th 4204

XX REL POSITION

1-4 zz

Relay Position

1-4 = relay position

[∗] to continue

This is the actual (or physical) relay number with respect to the Relay

Module upon which it is located. For 4204 modules, relay numbers

are 1-4. For 4229 modules, relay numbers are 1-2; for 6164 the relay

number is 1.

The system returns to the Output Number prompt for programming

the next device.

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 79 80

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-48D Especificaciones Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-48D