ADEMCO VISTA-48D Especificaciones descargar pdf (Pagina 30)

Installation Instructions

4-2

FIELD

TITLE and DATA ENTRIES EXPLANATION

*27

Powerline Carrier Device (X-10)

House ID

0 = A 6 = G # + 11 = L

1 = B 7 = H # + 12 = M

2 = C 8 = I # + 13 = N

3 = D 9 = J # + 14 = O

4 = E # + 10 = K # + 15 = P

5 = F

Powerline Carrier devices require a House ID, identified in this field.

Program Powerline Carrier devices in interactive modes ∗79, *80 and

*81.

Not intended for fire or UL installations.

*28

Language Select

0 = English 2 = Italian

1 = Spanish 3 = Portuguese

Select the desired keypad display language.

UL installations must be 0 (English)

*29

ECP Contact ID Output for ACM

0 = not used

1 = use Contact ID output on ECP

If selected, all messages programmed to go to the primary telephone

line receiver will also be sent (in Contact ID format) to the connected

Alternative Communication Media (ACM), such as a 7845i

Internet/Intranet Communicator or AI4164RS/AI4164ETH Eureka

Network Interface, or 7845C/7835C cellular radio (in selected

countries). The data line is supervised as well as certain functions in

a long range radio. If communication is lost or a trouble develops, an

attempt will be made to send a message via both ACM and telephone

to the central station.

Program the ACM for device address 3.

*30

Make Partition 3 a Common Area

Partition

0 = no (must be 0 if system uses zone type

82 - Blockschloss)

1 = yes, make partition 3 a common area

partition

If selected, partition 3 functions as a common area partition, rather

than as an independent partition.

Zone Sounds & Timing

FIELD

TITLE and DATA ENTRIES EXPLANATION

*31

Single Alarm Sounding Per Zone/

Dialer/Bell Disable if Arm Stay

0 -7 = see table of entries at right

Select whether a zone going into alarm should sound more than once

per armed period and whether Bell and/or Dialer should be disabled if

armed STAY.

UL installations must be 0 (no limit).

Entry Single Alarm

Sound

Disable Bell if

Armed STAY

Disable Dialer if

Armed STAY

No UL: must be “0”

No No

1 Yes No No

2 No Yes No

3 Yes Yes No

4 No No Yes

5 Yes No Yes

6 No Yes Yes

7 Yes Yes Yes

*32

Fire Alarm Sounder Timeout

0 = yes; fire sounder timeout after time

programmed in field ∗33

1 = no fire sounder timeout; continue

sounding until manually turned off

Select whether fire alarm sounding expires after sounder timeout or

remains until manually turned off.

UL fire alarm installations: must be 1.

*33

Bell (Siren) Timeout

0 = No timeout 4 = 4 min

1 = 1 min 5 = 8 min

2 = 2 min 6 = 16 min

3 = 3 min

This field determines whether the external sounder will shut off after

time allotted, or continue until manually turned off.

UL installations: For residential fire alarm installation, must be set

for a minimum of 4 min (option 4); for UL Commercial Burglary

installations, must be minimum 16 min (option 6).

*34

Exit Delay

00 - 96 = 0 - 96 seconds

97 = 120 seconds

The system waits the time entered before arming entry/exit zones. If

the entry/exit door is left open after this time expires, an alarm will

occur or the zone will be auto-bypassed, depending on the selection in

field *88. Common area zones use same delay as partition 1.

UL installations: For UL Commercial Burglar Alarm (Grade AA) and

UL Residential Burglar Alarm installations with line security, total

exit time must not exceed 60 seconds. For UL Burglar Alarm

installations without line security (Grade A), total exit time must not

exceed 120 seconds.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 79 80

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-48D Especificaciones Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-48D