ADEMCO VISTA-48D Especificaciones descargar pdf (Pagina 32)

Installation Instructions

4-4

FIELD

TITLE and DATA ENTRIES EXPLANATION

*44

Part. 1 Secondary Subs. Acct. No.

Enter digits 0–9; # + 11 for B, # + 12 for C, #

+ 13 for D, # + 14 for E, # + 15 for F.

Enter up to 10 digits, depending on the report format selected in field

*48. To clear entries from field, press ∗44∗.

*45

Part. 2 Primary Subs. Acct. No.

Enter digits 0–9; # + 11 for B, # + 12 for C, #

+ 13 for D, # + 14 for E, # + 15 for F.

Enter up to 10 digits, depending on the report format selected in field

*48. To clear entries from field, press ∗45∗.

*46

Part. 2 Secondary Subs. Acct. No.

Enter digits 0–9; # + 11 for B, # + 12 for C, #

+ 13 for D, # + 14 for E, # + 15 for F.

Enter up to 10 digits, depending on the report format selected in field

*48. To clear entries from field, press ∗46∗.

*47

Phone System Select/Dialer

Attempts

Phone System Select:

If Central Station Receiver is not on satellite

link: 0 = Decadic Pulse Dial;

1 = Multifrequency Tone Dial

If Central Station Receiver is on satellite link:

2 = Decadic Pulse Dial;

3 = Multifrequency Tone Dial

Dialer Attempts: 1 – 10 (for 10, enter #+10)

Phone System Select: Select the type of telephone service.

Dialer Attempts: Enter the number of times the system should

attempt to dial the central station, 1 – 10 times (for 10, enter #+10).

*48

Report Format (Primary/Secondary)

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = CID* using 10-digit account number

6 = 4+2 ADEMCO EXPRESS

7 = CID* using 4-digit account number

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

10 = ROBOFON 8 (6-digit account number)

11 = ROBOFON Contact ID

Select report format for primary and secondary phone numbers.

* ADEMCO Contact ID format

NOTE: To enable the audio “beeps” format (Follow-Me feature), refer

to the System Features section later in this manual, and the User

Guide.

*49

Split/Dual Reporting

0 = disable (standard/backup report only).

1 - 5 (see table to right)

To Primary No. To Secondary No.

1 = alarms, restore, cancel others

2 = all except open/close, test open/close, test

3 = alarms, restore, cancel all

4 = all except open/close, test all

5 = all all

*50

Burglary Dialer Delay

0 = no dial delay (UL: must be “0”)

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

Provides delay of “BURGLARY ALARM” report to the central station,

which allows time for the subscriber to avoid a false alarm

transmission. This delay does not apply to zone type 24 alarms (silent

burglary) or to 24-hour zone types 6, 7, and 8 (silent panic, audible

alarm, auxiliary alarm), which are always sent as soon as they occur.

*51

Part. 3 Primary Subs. Acct. No.

Enter digits 0–9; # + 11 for B, # + 12 for C, #

+ 13 for D, # + 14 for E, # + 15 for F.

Enter up to 10 digits, depending on the report format selected in field

*48.

*52

Part. 3 Secondary Subs. Acct. No.

Enter digits 0–9; # + 11 for B, # + 12 for C, #

+ 13 for D, # + 14 for E, # + 15 for F.

Enter up to 10 digits, depending on the report format selected in field

*48.

*53

SESCOA/Radionics Select

0 = Radionics (0-9, B-F reporting)

1 = SESCOA (0-9 only reporting)

Select SESCOA or Radionics format.

Select 0 for all other formats.

*54

Dynamic Signaling Delay

0 = disabled (both signals sent)

1–15 = entry times a 15-second delay.

e.g., 1 = 15 seconds, 2 = 30 seconds, etc.

Intended for use with ECP Contact ID Output reporting via ACM.

This field lets you select the time the panel should wait for

acknowledgment from the first reporting destination (see ∗55) before

it attempts to send a message to the second destination. Delays can

be selected from 0 to 225 seconds, in 15-second increments. This delay

is per message. If ”0” is entered in this field, the control panel will

send redundant reports to both Primary Dialer and ECP output.

UL Installations: For Fire Alarm and UL Burglar Alarm installations

without Line Security (Grade A), the maximum Dynamic

Signaling Delay must be no more than 15 seconds.

For UL Burglar Alarm installations with Line Security (Grade

AA), Dynamic Signaling Delay must be “0”. The reports will be sent to

both the dialer and the LRR.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 79 80

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-48D Especificaciones Pagina 32

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-48D