ADEMCO VISTA-48D Especificaciones descargar pdf (Pagina 22)

Installation Instructions

3-2

Keypads

Keypads are identified by predefined addresses (starting at address 16) as follows:

Address Keypad Program Field

16 keypad 1 • always enabled for partition 1, all sounds enabled. NOTE: First keypad is address 16.

17 keypad 2 • data field *190

18 keypad 3 • data field *191

19 keypad 4 • data field *192

20 keypad 5 • data field *193

21 keypad 6 • data field *194

22 keypad 7 • data field *195

23 keypad 8 • data field *196

To enable keypads:

1. Set desired address at keypad (refer to keypad’s instructions for setting the address).

2. Use data field program mode to enable keypad addresses, assign a partition, enable sound options

in fields *190-*196 as shown in the table above.

3. If desired, use data field *198 to turn on the display of the partition number.

4. Set the following keypad-related data fields as required by the installation:

*21 Quick Arm Enable ∗180 Zone Bypass Limit

*23 Forced Bypass ∗186 Display Options

∗25 Arming Prevention Override ∗188 Keypad Sabotage Options

*84 Auto STAY Arm

†

∗197 Exit Time Display Interval

∗88 Exit Options † NOTE: Do not use this option if Telecommand is installed to permit

remote end-user control of the system.

Wireless Receiver Transmitters, and Wireless Keys (keyfobs)

Receiver: Set the receiver’s address to “00” using its DIP switches, then set the following options:

*22 RF Jam Option

††

*24 RF House ID Code (if using DIP switch equipped wireless keypads) for each partition

∗25 Arming Prevention Override

*67 Transmitter Low Battery Report Code

††

*75 Transmitter Low Battery Restore Report Code

††

∗173 RF Reporting Options

∗178 RF Supervision/RF Jam Options

Use *56 Menu mode to program wireless zones 9-48 and wireless button zones 49-64.

Transmitters: Use *56 or *58 Zone Programming Menu modes to program zone information and

enroll transmitters (zones 9-48, buttons 49-64).

Wireless Keys: Use Wireless Key Programming Templates section of the *58 Zone Programming

Menu mode to program zone information and enroll each button of the wireless keys used. Once a

wireless key is enrolled, it must be assigned to a user before it becomes active. See Adding/Deleting

Security Codes section for procedure.

Pager Programming

The system can send various reports to up to 3 pagers.

To program pager reporting, do the following:

1. Enter the appropriate information in the following data fields:

*160, *163, *166 Pager Phone Numbers (for pagers 1-3 respectively)

*161, *164, *167 Pager Prefix Characters (for pagers 1-3 respectively)

*162, *165, *168 Pager Reporting Options by Partition

†

(for pagers 1-3 respectively)

2. Enable Pager Delay, if desired, in field *169 (delays alarm reporting for ALL pagers).

3. Enable appropriate user open/close pager reports using the user attribute command

(master code + [8] + user no. + [#] [5] + [1]). Users that perform actions in their assigned partition

will, if enabled, attempt to report to all pagers enabled for open/close reporting in that partition.

†† These fields must be enabled for Residential

Fire, UL Residential Burglar Alarm, and UL

Commercial Burglar Alarm installations.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 79 80

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-48D Especificaciones Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-48D