ADEMCO VISTA-100 Manual de usuario Pagina 15
- Pagina / 234
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 1 - General Description
1-xv
Auxiliary Relay
Provides a built-in Form C relay which can be used for one of the following purposes:
• Alarm activation
• Trouble/supervisory activation
• 4-wire smoke detector reset
• Battery-saving feature (disconnects power from noncritical loads 4 hours after AC power
loss)
Optional Output Relays
Accommodates the use of 16 relay outputs using ADEMCO's 4204 and 4204CF Relay
Modules. Each 4204 module provides four Form C relays for general-purpose use. Each
4204CF provides two style Y supervised bell outputs. Relay outputs have the following
characteristics:
• Can be programmed to activate in response to system events
• Can be programmed to activate using time intervals
• Can be used for additional style Y supervised bell outputs (4204CF only)
• Can be activated manually using the #70 relay command mode
• Can be supervised by the control panel (zones 601-632)
• Can each have an alpha descriptor assigned to it
Optional VISTA Interactive Phone Module
Supports the ADEMCO 4285/4286 VIP Module. This allows the security system to perform
the following tasks:
• Obtain system status information
• Arm and disarm security system
• Control relays
U
L
The 4285/4286 VIP Module is not UL Listed for use with the VISTA-100 control panel
.
Access Control
If programmed, provides users with a command which activates a relay for 2 seconds to
open access doors (e.g., lobby door). Each partition can be assigned an access control relay.
U
L
The access control function is not UL Listed for use with the VISTA-100 control panel.
Optional 24-Volt Power Supply
Compatible with the PS24 Power Supply Module, which supplies:
• Two 24VFW, 1.7A full-wave rectified, unfiltered outputs
• Used to power alarm notification appliances (sirens, strobes, etc.)
• Used to power auxiliary devices which can operate using full-wave rectified, unfiltered
voltage
- VISTA-100 1
- Table of Contents 4
- List of Figures 9
- How To Use This Manual 10
- 00 INSTALLER CODE 11
- General Description 12
- Section 8: 13
- Wireless Expansion 13
- Planning a Partitioned System 18
- Common Lobby Logic 19
- COMMON LOBBY 20
- In This Section 24
- Recent Close Report 25
- Exit Delay Reset 25
- Cross Zoning 25
- Call Waiting Defeat Logic 26
- Installing The Control 28
- Installing The Keypads 32
- Figure 5-2 33
- Mounting the Keypads 34
- Programming Remote Keypads 35
- Basic Hardwired Zones 001-008 36
- 2-WIRE SMOKE 37
- DETECTOR 37
- Figure 6.2 38
- Zone 6 Tamper Configuration 39
- 2-Wire Polling Loop Expansion 42
- (Zones 9 - 87) 42
- Wire Gauge Max. Length 43
- #22 gauge 650 feet 43
- #20 gauge 950 feet 43
- #18 gauge 1500 feet 43
- #16 gauge 2400 feet 43
- Section 17: 44
- Power-Up Procedure 44
- Polling Loop Supervision 46
- Wireless Zone Expansion 48
- 1 2 3 4 5 50
- Programming the RF Receiver 51
- House ID Sniffer Mode 51
- 5700 Series Transmitter Setup 52
- 5800 Series Transmitter Setup 54
- Relay Outputs 58
- 121110987654321 59
- 4285/4286 VIP Module 62
- Wiring the VIP Module 63
- Programming the VIP Module 64
- Section 18: 67
- The Mechanics of 67
- Programming 67
- J2 Trigger Outputs 70
- 5140LED Indicator Module 73
- 7720 WIRING DIAGRAM 75
- BURGLARY/AUDIBLE 76
- PANIC ALARM 76
- Event Log Printer Connections 77
- Direct Wire Downloading 77
- External Sounders 79
- Programming the Bell Outputs 80
- (Model 610-7) 81
- Auxiliary Relay 82
- Four-Wire Detector Circuit 83
- Section 14- Auxiliary Relay 84
- Dialer Outputs 85
- Dialer Operation 86
- Section 15- Dialer Outputs 87
- Event Log Options 88
- Programming Event Log Options 89
- Event Logging Procedures 90
- Section 16- Event Log Options 92
- Final Power-Up Procedure 93
- Backup Power Calculations 94
- Cannot exceed 128MA 95
- BATTERY SELECTION TABLE 98
- Section 17 – Final Power-Up 99
- The Mechanics Of Programming 100
- Viewing Data Fields 101
- Entry Errors 101
- #93 Menu Mode Programming 103
- Zone Type Definitions 104
- Zone Index/Zone Type Defaults 108
- Zone Type Defaults 109
- Data Field Descriptions 110
- 995 996 999 112
- Prm. Sec 115
- 95 96 99 Duress 116
- [15 15 15 15] 117
- Alm Chck Byps O/C Systm Test 120
- Bell 1 Bell 2 123
- Main Backup 124
- 16 17 18 124
- Bell 2 Aux 124
- Bell 2 Aux. Rly 125
- Zone Programming 128
- 010 LEARN S/N? 131
- 1 = YES, 0 = NO 1 131
- 010 INPUT S/N 131
- Axxx-xxxx 131
- Zone Number Entered 133
- Report Code Programming 135
- Programming Alpha Descriptors 138
- ****DISARMED**** 141
- READY TO ARM 141
- ****DISARMED**** 141
- (For Adding Custom Words) 143
- Device Programming 144
- Relay Programming 145
- Zone List Programming 149
- Relay Voice Descriptors 150
- CUSTOM INDEX? 151
- 0=no 1=yes 151
- CUSTOM WORD NO 151
- RF Serial Number Clear Mode 152
- Scheduling Options 153
- Time Windows Definitions 155
- Open/Close Definitions 157
- Programming Time Windows 160
- Daily Open/Close Worksheet 161
- Programming Holiday Schedules 163
- Time-Driven Event Worksheet 164
- Time-Driven Event Programming 166
- Access Control Schedules 168
- #83 User Scheduling Menu Mode 172
- System Communication 174
- Downloading Primer 184
- On-Line Control Functions 185
- Access Security 186
- J2 CONNECTOR 187
- Setting The Real-Time Clock 188
- User Access Codes 190
- User 3 User 3 193
- Level 1 Level 4 193
- Master Oper B 193
- To EXIT the User Edit Mode 195
- Keypad Functions 196
- Global Arming 197
- Closing Delay? 198
- Hit 0-2 Hours 198
- Viewing Zone Descriptors 199
- Viewing Downloaded Messages 199
- Panic Keys 199
- Speed Key “D” (Macros) 199
- ENTER SPEED KEY 200
- "D" 200
- ENTER DEVICE NO 200
- 00=QUIT 01 200
- HIT 0=OFF , 1=ON 201
- HIT THE "*" KEY 201
- Testing The System 202
- DISARMED 203
- DISARMED Press 203
- Battery Test 205
- Dialer Test 205
- Armed Burglary System Test 207
- Trouble Conditions 208
- To the Installer 209
- Regulatory Agency Statements 212
- Appendix A-4 215
- Appendix A-5 216
- Appendix A-6 217
- DIP Switch Tables 218
- Appendix B-3 220
- Appendix B-4 221
- Summary of System Commands 222
- Specifications 224
- DIGITAL COMMUNICATOR 225
- 6139(R) REMOTE KEYPAD 225
- WARNING! 230
- Appendix-6 231
- SUMMARY OF CONNECTIONS 233
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-100
(8 paginas)
(56 paginas)
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales