ADEMCO VISTA-100 Manual de usuario Pagina 14
- Pagina / 234
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VISTA-100 Installation Instructions
1-xiv
• Certain system options are selectable for each partition, such as Entry/Exit Delay and
subscriber account number
User Codes
Accommodates 128 user codes, all of which can operate any or all partitions. The following
characteristics must be assigned to each user code:
• Authority level (Master, Manager, or several other Operator levels)
• Opening/closing central station reporting option
• Which partitions the code can operate
• Global arming capability (the ability to arm all partitions to which the code has access in
one command)
• Use of an RF (button) to arm and disarm the system (RF key must first be programmed
into the system)
Peripheral Devices
Supports up to 31 addressable devices, which can be any combination of keypads
(6139/6139R), RF receivers (4281/5881), relay modules (4204/4204CF), and 4285/4286 VIP
Module. Peripheral devices have the following characteristics:
• Each device is set to an individual address (physically) according to the device's
instructions
• Each device is enabled in the system using the Device Programming Mode (see “Device
Programming” in Section 22: #93 Menu Mode Programming)
At least one 2-line alpha keypad (6139/6139R) must be connected to the system for programming
(if using keypad programming) and must remain connected to the system in order to allow the
primary user to program additional user codes into the system at a later time.
Keypad Panic Keys
Accommodates three keypad panic keys: 1 +
✴
(A),
✴
+ [#] (B), and 3 + [#] (C).
• Designated as zones 995 (1 +
✴
), 996 (3 + [#]), and 999 (
✴
+ [#])
• Activated by wired and wireless keypads
• Activated and reported separately by partition, distinguished by subscriber account
number (or partition number if Contact ID reporting is used)
Keypad Macros
Accommodates one keypad macro command per partition (each macro is a series of keypad
commands), which can be assigned to the "D" key on each partition's keypads. This means,
for example, that by pressing the "D" key, the system can be programmed to log onto
another partition, bypass zones 2 and 3, and arm that partition in the AWAY mode (See
Section 28: Keypad Functions). Characteristics of keypad macros are:
• Assignable to the "D" key by partition
• Can each be 16 characters (keystrokes) in length
Bell Outputs
Provides two style-Y supervised bell outputs on the control panel itself. A 4204CF Relay
Module can supply two additional style Y supervised bell outputs.
- VISTA-100 1
- Table of Contents 4
- List of Figures 9
- How To Use This Manual 10
- 00 INSTALLER CODE 11
- General Description 12
- Section 8: 13
- Wireless Expansion 13
- Planning a Partitioned System 18
- Common Lobby Logic 19
- COMMON LOBBY 20
- In This Section 24
- Recent Close Report 25
- Exit Delay Reset 25
- Cross Zoning 25
- Call Waiting Defeat Logic 26
- Installing The Control 28
- Installing The Keypads 32
- Figure 5-2 33
- Mounting the Keypads 34
- Programming Remote Keypads 35
- Basic Hardwired Zones 001-008 36
- 2-WIRE SMOKE 37
- DETECTOR 37
- Figure 6.2 38
- Zone 6 Tamper Configuration 39
- 2-Wire Polling Loop Expansion 42
- (Zones 9 - 87) 42
- Wire Gauge Max. Length 43
- #22 gauge 650 feet 43
- #20 gauge 950 feet 43
- #18 gauge 1500 feet 43
- #16 gauge 2400 feet 43
- Section 17: 44
- Power-Up Procedure 44
- Polling Loop Supervision 46
- Wireless Zone Expansion 48
- 1 2 3 4 5 50
- Programming the RF Receiver 51
- House ID Sniffer Mode 51
- 5700 Series Transmitter Setup 52
- 5800 Series Transmitter Setup 54
- Relay Outputs 58
- 121110987654321 59
- 4285/4286 VIP Module 62
- Wiring the VIP Module 63
- Programming the VIP Module 64
- Section 18: 67
- The Mechanics of 67
- Programming 67
- J2 Trigger Outputs 70
- 5140LED Indicator Module 73
- 7720 WIRING DIAGRAM 75
- BURGLARY/AUDIBLE 76
- PANIC ALARM 76
- Event Log Printer Connections 77
- Direct Wire Downloading 77
- External Sounders 79
- Programming the Bell Outputs 80
- (Model 610-7) 81
- Auxiliary Relay 82
- Four-Wire Detector Circuit 83
- Section 14- Auxiliary Relay 84
- Dialer Outputs 85
- Dialer Operation 86
- Section 15- Dialer Outputs 87
- Event Log Options 88
- Programming Event Log Options 89
- Event Logging Procedures 90
- Section 16- Event Log Options 92
- Final Power-Up Procedure 93
- Backup Power Calculations 94
- Cannot exceed 128MA 95
- BATTERY SELECTION TABLE 98
- Section 17 – Final Power-Up 99
- The Mechanics Of Programming 100
- Viewing Data Fields 101
- Entry Errors 101
- #93 Menu Mode Programming 103
- Zone Type Definitions 104
- Zone Index/Zone Type Defaults 108
- Zone Type Defaults 109
- Data Field Descriptions 110
- 995 996 999 112
- Prm. Sec 115
- 95 96 99 Duress 116
- [15 15 15 15] 117
- Alm Chck Byps O/C Systm Test 120
- Bell 1 Bell 2 123
- Main Backup 124
- 16 17 18 124
- Bell 2 Aux 124
- Bell 2 Aux. Rly 125
- Zone Programming 128
- 010 LEARN S/N? 131
- 1 = YES, 0 = NO 1 131
- 010 INPUT S/N 131
- Axxx-xxxx 131
- Zone Number Entered 133
- Report Code Programming 135
- Programming Alpha Descriptors 138
- ****DISARMED**** 141
- READY TO ARM 141
- ****DISARMED**** 141
- (For Adding Custom Words) 143
- Device Programming 144
- Relay Programming 145
- Zone List Programming 149
- Relay Voice Descriptors 150
- CUSTOM INDEX? 151
- 0=no 1=yes 151
- CUSTOM WORD NO 151
- RF Serial Number Clear Mode 152
- Scheduling Options 153
- Time Windows Definitions 155
- Open/Close Definitions 157
- Programming Time Windows 160
- Daily Open/Close Worksheet 161
- Programming Holiday Schedules 163
- Time-Driven Event Worksheet 164
- Time-Driven Event Programming 166
- Access Control Schedules 168
- #83 User Scheduling Menu Mode 172
- System Communication 174
- Downloading Primer 184
- On-Line Control Functions 185
- Access Security 186
- J2 CONNECTOR 187
- Setting The Real-Time Clock 188
- User Access Codes 190
- User 3 User 3 193
- Level 1 Level 4 193
- Master Oper B 193
- To EXIT the User Edit Mode 195
- Keypad Functions 196
- Global Arming 197
- Closing Delay? 198
- Hit 0-2 Hours 198
- Viewing Zone Descriptors 199
- Viewing Downloaded Messages 199
- Panic Keys 199
- Speed Key “D” (Macros) 199
- ENTER SPEED KEY 200
- "D" 200
- ENTER DEVICE NO 200
- 00=QUIT 01 200
- HIT 0=OFF , 1=ON 201
- HIT THE "*" KEY 201
- Testing The System 202
- DISARMED 203
- DISARMED Press 203
- Battery Test 205
- Dialer Test 205
- Armed Burglary System Test 207
- Trouble Conditions 208
- To the Installer 209
- Regulatory Agency Statements 212
- Appendix A-4 215
- Appendix A-5 216
- Appendix A-6 217
- DIP Switch Tables 218
- Appendix B-3 220
- Appendix B-4 221
- Summary of System Commands 222
- Specifications 224
- DIGITAL COMMUNICATOR 225
- 6139(R) REMOTE KEYPAD 225
- WARNING! 230
- Appendix-6 231
- SUMMARY OF CONNECTIONS 233
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-100
(8 paginas)
(56 paginas)
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.121 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales