ADEMCO VISTA-100 Manual de usuario Pagina 144
- Pagina / 234
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 22 - #93 Menu Mode Programming
22-5
Device Programming
Use this menu to program keypads, receivers, and relay modules.
From Data Field Programming Mode, press #93 to display "ZONE PROG?". Press 0
repeatedly to until "DEVICE PROG?" is displayed.
DEVICE PROG?
1=YES 0=NO
Press 1 to enter Device Programming Mode.
DEVICE ADDRESS
01-31, 00=QUIT
The device address identifies the device to the control. Enter
the 2-digit device address number to match the device's
physical address setting (01-30). Press
✴
to accept the
entry.
Note: You must use Device Address 04 for the 4285/4286 Voice
Module, if you are using one. If not, you can use Address 04
for another device type.
DEVICE TYPE
Select the type of addressable device as follows:
0 = device not used
1 = alpha keypad (6139/6139R)
3 = RF receiver (4281/5881)
4 = output relay module (4204)
5 = voice (VIP) module (4285/4286)
Press
✴
to accept the entry.
SUPERVISED CF?
If you selected device type 4 (output relay module) in the last
step, this prompt will appear. Enter 1 if the unit is a 4204CF.
If it is not, enter 0. If you enter 1, you will be able to program
only Relay 1 (Output A) and Relay 3 (Output B) for functions
on each module. This module is usually used to add two
additional supervised bell outputs to the system.
Press
✴
to continue.
CONSOLE PART.
If you selected device type 1 (alpha keypad), this prompt will
appear. Enter the addressable device's default partition
number (01 to the maximum number of partitions that you
programmed for the system in field 2*00). This is the primary
partition for which you intend to use the device. Enter 9 to
make this keypad a "Master" keypad for the system. Press
✴
to accept the entry.
RF EXPANDER
HOUSE ID XX
If you selected device type 3 (RF receiver), this prompt will
appear. Enter the 2-digit House ID (00-31). This is required
for 5700 Series systems only, or for using a wireless keypad
(5827/5827BD) with a 5800 Series system.
MODULE PART.
If you selected device type 5 (VIP Module), this prompt will
appear. Enter the partition number (1-8) in which the module
is located. Press
✴
to accept the entry.
- VISTA-100 1
- Table of Contents 4
- List of Figures 9
- How To Use This Manual 10
- 00 INSTALLER CODE 11
- General Description 12
- Section 8: 13
- Wireless Expansion 13
- Planning a Partitioned System 18
- Common Lobby Logic 19
- COMMON LOBBY 20
- In This Section 24
- Recent Close Report 25
- Exit Delay Reset 25
- Cross Zoning 25
- Call Waiting Defeat Logic 26
- Installing The Control 28
- Installing The Keypads 32
- Figure 5-2 33
- Mounting the Keypads 34
- Programming Remote Keypads 35
- Basic Hardwired Zones 001-008 36
- 2-WIRE SMOKE 37
- DETECTOR 37
- Figure 6.2 38
- Zone 6 Tamper Configuration 39
- 2-Wire Polling Loop Expansion 42
- (Zones 9 - 87) 42
- Wire Gauge Max. Length 43
- #22 gauge 650 feet 43
- #20 gauge 950 feet 43
- #18 gauge 1500 feet 43
- #16 gauge 2400 feet 43
- Section 17: 44
- Power-Up Procedure 44
- Polling Loop Supervision 46
- Wireless Zone Expansion 48
- 1 2 3 4 5 50
- Programming the RF Receiver 51
- House ID Sniffer Mode 51
- 5700 Series Transmitter Setup 52
- 5800 Series Transmitter Setup 54
- Relay Outputs 58
- 121110987654321 59
- 4285/4286 VIP Module 62
- Wiring the VIP Module 63
- Programming the VIP Module 64
- Section 18: 67
- The Mechanics of 67
- Programming 67
- J2 Trigger Outputs 70
- 5140LED Indicator Module 73
- 7720 WIRING DIAGRAM 75
- BURGLARY/AUDIBLE 76
- PANIC ALARM 76
- Event Log Printer Connections 77
- Direct Wire Downloading 77
- External Sounders 79
- Programming the Bell Outputs 80
- (Model 610-7) 81
- Auxiliary Relay 82
- Four-Wire Detector Circuit 83
- Section 14- Auxiliary Relay 84
- Dialer Outputs 85
- Dialer Operation 86
- Section 15- Dialer Outputs 87
- Event Log Options 88
- Programming Event Log Options 89
- Event Logging Procedures 90
- Section 16- Event Log Options 92
- Final Power-Up Procedure 93
- Backup Power Calculations 94
- Cannot exceed 128MA 95
- BATTERY SELECTION TABLE 98
- Section 17 – Final Power-Up 99
- The Mechanics Of Programming 100
- Viewing Data Fields 101
- Entry Errors 101
- #93 Menu Mode Programming 103
- Zone Type Definitions 104
- Zone Index/Zone Type Defaults 108
- Zone Type Defaults 109
- Data Field Descriptions 110
- 995 996 999 112
- Prm. Sec 115
- 95 96 99 Duress 116
- [15 15 15 15] 117
- Alm Chck Byps O/C Systm Test 120
- Bell 1 Bell 2 123
- Main Backup 124
- 16 17 18 124
- Bell 2 Aux 124
- Bell 2 Aux. Rly 125
- Zone Programming 128
- 010 LEARN S/N? 131
- 1 = YES, 0 = NO 1 131
- 010 INPUT S/N 131
- Axxx-xxxx 131
- Zone Number Entered 133
- Report Code Programming 135
- Programming Alpha Descriptors 138
- ****DISARMED**** 141
- READY TO ARM 141
- ****DISARMED**** 141
- (For Adding Custom Words) 143
- Device Programming 144
- Relay Programming 145
- Zone List Programming 149
- Relay Voice Descriptors 150
- CUSTOM INDEX? 151
- 0=no 1=yes 151
- CUSTOM WORD NO 151
- RF Serial Number Clear Mode 152
- Scheduling Options 153
- Time Windows Definitions 155
- Open/Close Definitions 157
- Programming Time Windows 160
- Daily Open/Close Worksheet 161
- Programming Holiday Schedules 163
- Time-Driven Event Worksheet 164
- Time-Driven Event Programming 166
- Access Control Schedules 168
- #83 User Scheduling Menu Mode 172
- System Communication 174
- Downloading Primer 184
- On-Line Control Functions 185
- Access Security 186
- J2 CONNECTOR 187
- Setting The Real-Time Clock 188
- User Access Codes 190
- User 3 User 3 193
- Level 1 Level 4 193
- Master Oper B 193
- To EXIT the User Edit Mode 195
- Keypad Functions 196
- Global Arming 197
- Closing Delay? 198
- Hit 0-2 Hours 198
- Viewing Zone Descriptors 199
- Viewing Downloaded Messages 199
- Panic Keys 199
- Speed Key “D” (Macros) 199
- ENTER SPEED KEY 200
- "D" 200
- ENTER DEVICE NO 200
- 00=QUIT 01 200
- HIT 0=OFF , 1=ON 201
- HIT THE "*" KEY 201
- Testing The System 202
- DISARMED 203
- DISARMED Press 203
- Battery Test 205
- Dialer Test 205
- Armed Burglary System Test 207
- Trouble Conditions 208
- To the Installer 209
- Regulatory Agency Statements 212
- Appendix A-4 215
- Appendix A-5 216
- Appendix A-6 217
- DIP Switch Tables 218
- Appendix B-3 220
- Appendix B-4 221
- Summary of System Commands 222
- Specifications 224
- DIGITAL COMMUNICATOR 225
- 6139(R) REMOTE KEYPAD 225
- WARNING! 230
- Appendix-6 231
- SUMMARY OF CONNECTIONS 233
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-100
(8 paginas)
(56 paginas)
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales