– 8 –
Programming a Data Field
1. Press [
✱
] plus Field No. (for example,
✱
21), then make the desired entry.
2. When you have completely programmed a data field, the keypad will “beep”
three times and then automatically display the next data field in sequence.
To go to a different field, press [
✱
] plus the desired field No.
3. If the number of digits that you need to enter in a data field is less than the
maximum digits available (for example, the phone number field), enter the
desired data, then press
✱
and the next data field number to be programmed.
4. If you try to enter a non-existent field, an Alpha keypad will display NOT
USED and EE (Entry Error). Simply key [
✱
] again plus a valid field number.
Reviewing a Data Field/Erasing an Entry in a Data Field
Press [#] plus Field No. Data will be displayed for that field number. No
changes will be accepted in this mode.
To delete an entry in a field, press [
✱
] plus Field No. + [
✱
]. (Applies only to
fields
✱
40 –
✱
42, and
✱
94.)
Interactive Menu Mode Programming (
✱
56,
✱
80,
✱
81,
✱
82 and
✱
83)
Typical prompt displayed
during interactive menu
mode programming
Enter Zn Num.
(00 = Quit) 01
Zone Number ↑
Press [
✱
] plus menu mode No. (for example,
✱
56). The Alpha keypad will
display the first of a series of prompts requesting entries.
A detailed procedure (with displays of prompts) is provided in those sections in
the Installation Instructions where programming in the menu mode is to be
performed.
Menu Mode Used To Program
✱
56 Zone Programming Zone characteristics, report codes, alpha descrip-
tors and serial numbers for 5800 transmitters
✱
80 Relay Programming 4204 Relay modules
✱
81 Zone List Programming Zone Lists for 4204 relay activation
✱
82 Alpha Programming Zone alpha descriptors
✱
83 Sequential Mode 5800 series transmitter serial numbers
Loading Factory Defaults (
✱
97)
To load the Ademco factory defaults, enter the programming mode, press
✱
97,
then exit the programming mode.
Do not press
✱
97 if you program new values in place of the factory defaults—
the new values will be changed back to the factory default values!
✱
96 resets the Subscriber Account number and CSID in preparation for an
initial download.
Programming System Setup Fields
The following program fields MUST be programmed (as required) before
doing any programming.
✱
22 RF SYSTEM (Default is 0).
Enter “1” if 5700 RF system type is being used; enter “2” if a 5800 RF
system type is being used; enter “0” if no RF is being used.
✱
25 OUTPUT RELAY MODULE (Default is 0).
Enter “3” if a 4204 relay is being used, or “0” if a relay is not being used.
Exiting the Programming Mode
✱
98 EXITS PROGRAMMING MODE and prevents re-entry by Installer
Code + [8] + [0]. To enter the programming mode if
✱
98 was used to exit,
you must first power the system down. Then power up again, and press
[
✱
] and [#] both at once, within 50 seconds of powering up.
✱
99 EXITS PROGRAMMING MODE and allows re-entry by:
Installer Code + [8] + [0] or by:
Pressing [
✱
] and [#] at the same time, within 50 seconds of powering up
the system.
(17 paginas)
(56 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales