ADEMCO Security System VISTA-10SE Manual de usuario descargar pdf (Pagina 5)

– 5 –

RF EXPANSION ZONES: With 4281L, up to 4 RF expansion zones available; 4281M or 4281H, up to 8; ENTER FOR

5881L, up to 8; 5881M or 5881H, up to 16.

↓

5800 ONLY

↓

ZONE ZONE ZONE ALARM RPT CODE INPUT RF INPUT

DESCRIPTION No. TYPE (Hex) DEVICE LOOP

(Zn) (ZT) (RC) (in) (L)

5th

6th

7th

8th

9th

10th

11th

12th

13th

14th

15th

16th

EXPLANATION OF ZONE ASSIGNMENT TABLE

Zn = ZONE NUMBER Zone Nos. are from 01 to 63, 95, 96. Some are pre-assigned.

With Field ✱22 set for RF (5700 or 5800), use Zone Nos. 10-63 .

ZT = ZONE TYPE 00 = Zone Not Used

01 = Entry/Exit

02 =

Do not use

03 = Perimeter

04 = Interior Follower

05 = Trouble Day/Alarm Night

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

09 = Fire

10 = Interior w/Delay

20 = Arm–Stay *

21 = Arm–Away*

22 = Disarm*

23 = No Alarm Response

* 20, 21, & 22 used for 5800 RF systems only.

RC = ALARM REPORT CODE Two Hex Digits. For each Hex Digit, enter: 00–09 for 0–9, 10 for A, 11 for B, 12 for C, 13 for D, 14 for E, 15 for F.

If "00" is entered in the first pair of boxes, there will be no report for that zone.

For contact ID reporting, this is an enabling code only. Make any hex digit entry (other than "00") in the first

pair of boxes. The second pair of boxes will be ignored.

In = RF INPUT DEVICE

HW: Hard Wire Enter 3 for RF: Supervised RF (this is the default)

Enter 4 for UR: Unsupervised RF

Enter 5 for BR: Button Type RF

L = RF INPUT LOOP Used with 5800 RF Input Devices. Record transmitter input number.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT

CODES (✱ 60 – ✱ 75):

With a 3+1 or 4+1 Standard Format: Enter a code in the

first

box: 1-9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B,

"#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F.

A "0" (

not

"#+10") in the

first

box will disable a report.

A "0" (

not

"#+10") in the

second

box will result in automatic

advance to the next field when programming.

With an Expanded or 4+2 Format: Enter codes in

both

boxes

(1st and 2nd digits) for 1-9, 0, or B-F, as described above.

A "0" (

not

"#+10") in the

second

box will eliminate the ex-

panded message for that report.

A "0" (

not

"#+10") in

both

boxes will disable the report.

With Ademco Contact ID Reporting: Enter any digit (other than

"0") in the

first

box, to enable zone to report (entries in the

second

boxes will be ignored).

A "0" (

not

"#+10") in the

first

box will disable the report.

Examples:

For Code 3 (Single Digit), enter: 3 0

For Code 32 (Two Digits), enter: 3 2

For Code B2 (Hexadecimal) enter: #+11 2

SYSTEM STATUS REPORT CODES (✱60 – ✱68)

✱60 TROUBLE REPORT CODE

✱61 BYPASS REPORT CODE

✱62 AC LOSS REPORT CODE

✱63 LOW BATTERY REPORT CODE

✱64 TEST REPORT CODE

✱65 OPEN/EXIT ALARM REPORT CODE /

2nd digit of OPEN REPORT is automatically sent as the

user number if expanded or 4+2 reporting is selected.

2nd digit of EXIT ALARM REPORT is automatically sent as

the 2nd digit of the zone alarm report code programmed in

✱56, if expanded or 4+2 reporting is selected.

✱66 AWAY/STAY CLOSE REPORT CODE /

2nd digit of any CLOSE REPORT is automatically sent as the user

number, if expanded or 4+2 reporting is selected.

✱67 RF XMTR LOW BAT REPORT CODE

✱68 CANCEL REPORT CODE

RESTORE REPORT CODES (✱70 – ✱75)

✱70 ALARM RESTORE REPORT CODE

2nd digit is automatically sent as the 2nd digit of the

zone alarm report code programmed in ✱ 56, if

expanded or 4+2 reporting is selected.

✱71 TROUBLE RESTORE REPORT CODE

✱72 BYPASS RESTORE REPORT CODE

✱73 AC RESTORE REPORT CODE

✱74 LOW BAT RESTORE REPORT CODE

✱75 RF XMTR LO BAT RST REPORT CODE

1 2 3 4 5 6 7 8 9 10 ... 23 24

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-10SE Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE