ADEMCO Security System VISTA-10SE Manual de usuario descargar pdf (Pagina 15)

– 15 –

✱

45 PHONE SYSTEM SELECT (1-Digit Entry) Default is 0.

If Central Station Receiver is not on WATS line:

0 = Pulse Dial 1 = Tone Dial

If Central Station Receiver is on WATS line:

2 = Pulse Dial 3 = Tone Dial

For an explanation of these

formats, see the SYSTEM

COMMUNICATION

section in the Installation

Instructions.

✱

46 REPORT FORMAT (1-Digit Entry) Default is 0.

Determine which format is to be used to report to the central station.

Enter 1 digit (0–9).

0 = 3+1; 4+1 ADEMCO Lo Speed Standard (this is the default)

1 = 3+1; 4+1 Radionics Standard

2 = 4+2 ADEMCO Lo Speed Standard

3 = 4+2 Radionics Standard

6 = 4+2 ADEMCO Express

7 = ADEMCO Contact ID Reporting

8 = 3+1; 4+1 ADEMCO Lo Speed Expanded

9 = 3+1; 4+1 Radionics Expanded

(Enter

✱

as the 4th digit of

✱

43 if 3+1 dialer reporting is to be used.)

Note: The maximum number of alarm and alarm restore reports

during one armed period is determined by field

✱

92.

See field

✱

27, which may override this field’s selection.

✱

47 SPLIT/DUAL REPORTING (1-Digit Entry) Default is 0.

Enter 0 to disable (Backup report only).

Entries 1 through 9 can be made, as indicated in the table below. Entries

6 through 9 will send a report to a pager (in addition to the selected

primary phone number), but you must enter the pager number as the

secondary phone number in field

✱

42.

* Can only be used if the

Primary reporting format

is Ademco Contact ID.

If reporting to a Pager,

choose from 6, 7, 8, or 9,

as desired.

TO PRIMARY PHONE # TO SECONDARY PHONE #

1 = Alarms, Restore, Cancel Other Reports

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel All reports

4 = All except Open/Close, Test All reports

5 = All reports All reports

TO PRIMARY PHONE # TO PAGING No.* (Secondary)

6 = All reports except Open/Close Alarms/Open/Close, Troubles

7 = All reports Alarms, Troubles

8 = All reports Alarms/Open/Close, Troubles

9 = All reports except Open/Close Alarms, Open/Close for users #5–25

‡

Troubles

‡

Will report only Users 5, 6 & 8. If using 5800 series wireless button-type

devices, the zone number of the arm or disarm button (10–25) will be sent as

the user number.

Entries 6 through 9 will send a report to a pager (in addition to the selected

primary phone number), but you must enter the pager number as the secondary

phone number in field

✱

42.

A 10-digit code is sent to the pager which will take the following format:

†

4-digit Subscriber No.

→ SSSS–EEE–NNN

←

3-digit User or Zone No

(as entered in field

✱43) ↑

3-Digit Event Code (EEE), as follows:

911 = Alarm (NNN = Zone No.)

001 = Open, System disarmed (NNN = User No.)

002 = Close, System armed (

NNN = User No.)

811 = Trouble (

NNN = Zone No.)

†

The first digit of the Subscriber No. entered in field

✱

43 must be 1–9 (do not use 0); the

last 3 digits can be 0–9. Failure to observe this requirement may interfere with

paging services.

(Continued)

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 23 24

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-10SE Manual de usuario Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE