ADEMCO Security System VISTA-10SE Manual de usuario descargar pdf (Pagina 18)

– 18 –

✱

66 AWAY/STAY CLOSE REPORT CODE (2-Digit Entry)

(See box on previous page.)

To enable, enter a code (or 0 to disable) in either or both boxes.

For expanded or 4+2 reporting, 2nd digit for each = User # .

✱

67 RF XMTR. LOW BATTERY REPORT CODE (2-Digit Entry)

(See box on previous page).

✱

68 CANCEL REPORT CODE (2-Digit Entry)

(See box on previous page.)

RESTORE

REPORT CODES

(

✱

70 –

✱

75)

✱

70 ALARM RESTORE REPORT CODE

(See box on previous page). For expanded or 4+2 reporting, a 2nd digit is

automatically sent, and is the same as the 2nd digit of the zone alarm

report code programmed in field

✱

56.

✱

71 TROUBLE RESTORE REPORT CODE (2-Digit Entry)

(See box on previous page). This is sent when a trouble in a zone is

restored.

✱

72 BYPASS RESTORE REPORT CODE (2-Digit Entry)

(See box on previous page) . This is sent when a zone that has been

bypassed is un-bypassed.

✱

73 AC RESTORE REPORT CODE (2-Digit Entry)

(See box on previous page) . Reports with Subscriber No.

✱

74 LOW BAT RESTORE REPORT CODE (2-Digit Entry)

(See box on previous page). Reports with Subscriber No.

✱

75 RF XMTR. LOW BATTERY RESTORE CODE (2-Digit Entry)

(See box on previous page). This is sent when a transmitter that

previously sent in a low battery message has sent a message indicating

it no longer has a low battery condition.

✱

80 OUTPUT RELAYS

This is an interactive menu mode that is applicable only if 4204 relays

are to be used (“3” in field

✱

25). See the RELAY OUTPUTS section in

the Installation Instructions for a detailed programming procedure.

Also refer to the OUTPUT RELAY table for field

✱

80 in the

Programming Form in this manual.

✱

81 ZONE LISTS FOR OUTPUT DEVICES

This is an interactive menu mode that is applicable only if field

✱

25 is

programmed for a 4204 relay. Refer to the RELAY OUTPUTS section in

the Installation Instructions for a detailed programming procedure.

Also refer to the ZONE LISTS FOR OUTPUT RELAYS table for

✱

81 in

the Programming Form in this manual.

✱

82 CUSTOM ALPHA EDITING

See the ALPHA DESCRIPTION PROGRAMMING section in the

Installation Instructions for procedure.

✱

83 SEQUENTIAL MODE

May be used for enrolling transmitters in a 5800 RF system after all

other zone information has been programmed in

✱

56. See the

Installation Instructions for a detailed programming procedure.

✱

91 OPTION SELECTION (1-Digit Entry) Default is 0.

Enter “4” if an Audio Alarm Verification (AAV) unit is connected in the

system (1–3 not used); enter “0” if an AAV unit is not being used.

For UL installations, the AAV option must be disabled (0).

Important: AAV should not be used when Paging or Alarm Reports are

being sent to a Secondary number. If this is done, the call to the

Secondary number by the communicator after the alarm report will

prevent the AAV from taking control of the telephone line, and the AAV

“Listen in” session cannot take place.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-10SE Manual de usuario Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE