– 14 –
ZONE SOUNDS AND
TIMING
(
✱
28–
✱
39)
✱
28 SINGLE ALARM SOUNDING PER ZONE Default is 0.
(Per Armed Period) (1-Digit Entry)
This field limits external alarm sounding to once per arming period for
a given zone. Enter 1 for yes; 0 for no.
U
L
For UL installations, enter 0 for unlimited Alarm Soundings
✱
29 FIRE SOUNDER TIMEOUT (1-Digit Entry) Default is 0.
This field determines whether the external sounder will shut off after
time allotted, or continue until manually turned off. Enter 0 for sounder
timeout, or 1 for no timeout. Default is 0.
✱
30 ALARM BELL TIMEOUT (1-Digit Entry) Default is 1.
This field determines whether the external sounder will shut off after
time allotted, or continue until manually turned off. Enter as follows:
0 = No timeout; 1 = 4 min (default); 2 = 8 min; 3 = 12 min; 4 = 16 min.
✱
38 ENTRY DELAY (1-Digit Entry) Default is 2.
System will wait the time allotted before sounding alarm upon entering.
May be selected individually
0 = 0 seconds; 1 = 20 seconds; 2 = 30 seconds; 3 = 45 seconds;
4 = 60 seconds; 5 = 90 seconds.
(EXIT delay = Entry delay plus 15 seconds).
U
L
For UL installations, entry delay can be no greater than 45 seconds.
✱
39 AUDIBLE EXIT WARNING (1-Digit Entry) Default is 1.
If enabled, this field provides exit warning sound when armed AWAY or
MAXIMUM.
Warning sound consists of slow continuous beeps until last 5 seconds,
when it changes to fast beeps. The warning sound will end at the
termination of Exit time.
0 = no; 1 = yes.
DIALER
PROGRAMMING
(
✱
40–
✱
50)
✱
40 PABX ACCESS CODE (See Box at Left)
Enter up to 4 digits if PABX is needed to access an outside line. If
fewer than 4 digits are needed to be entered, exit by pressing
✱
and
next field number (e.g., 41). To clear entries from field, press
✱
40
✱
.
Fields
✱
40,
✱
41,
✱
42:
Enter up to the number
of digits shown. Do not
fill unused spaces.
Enter 0–9,
# + 11 for ‘
✱
’
# + 12 for ‘#’
# + 13 for a pause
(2.5 secs)
✱
41 PRIMARY PHONE No. (See Box at Left)
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing
✱
and next field number (e.g., 42). To clear entries from field, press
✱
41
✱
.
Note: Back-up reporting (8 calls are made to the secondary phone
number if no kiss-off is received after 8 attempts to primary
number) is automatic only if there is a secondary phone number
(field
✱
42).
✱
42 SECONDARY PHONE No. (See Box at Left)
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing
✱
and next field number (e.g., 43). To clear entries from field, press
✱
42
✱
. See Note in field
✱
41 also.
Note: If you wish to send a report to a pager, see field
✱
47 on
next page .
✱
43 SUBSCRIBER ACCOUNT. No. (Enter up to 4 digits).
Enter digits 0–9, #+11=B, #+12=C, #+13=D, #+14=E, or #+15=F.
Enter
✱
as the fourth digit if a 3 digit account no. (for 3+1 dialer
reporting format) is used. Enter 0 as the first digit of a 4-digit account
no. for nos. 0000–0999. End field by pressing
✱
(and press next field) if
only 3 digits are used.
This field is also used as the Long Range Radio Subscriber Account #.
(17 paginas)
(56 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales