ADEMCO Security System VISTA-10SE Manual de usuario descargar pdf (Pagina 19)

– 19 –

✱

92 NUMBER OF REPORTS IN ARMED PERIOD Default is 0.

(1-Digit Entry). This option can be used to limit the number of messages

(alarm & alarm restore reports) sent to the central station in an armed

period. “0” limits reports to a total of 10; “1” allows an unlimited

number of reports.

“1” must be selected for UL installations

DOWNLOAD

INFORMATION

(

✱

94,

✱

95)

✱

94 DOWNLOAD PHONE NUMBER

Enter up to 12 digits; 0–9, # +11 for “

✱

”, # + 12 for “#”, # + 13 for a

pause. Do not fill unused spaces. End field by entering

✱

. To clear

entries from field, press

✱

95 RING DETECTION COUNT FOR DOWNLOADING Default is 0.

Enter number of rings before control picks up phone line (or 0 or 15).

Refer to the chart below and program this field accordingly.

Phone Answering

Module Machine Downloading Field

✱

Yes No No Set for value other than “0” (1–14). This will

enable the control panel to answer the phone

call. Otherwise, it will not be possible to

access the Phone Module

Yes Yes No Set for a value higher than the number of

rings for which the answering machine is

set. Example: if machine is set for 4 rings,

use a value of 5 or higher. This is recom-

mended so that the Phone Module can still

be accessed if the answering machine is

turned off and does not answer the phone

call.

Yes No Yes Set for value other than “0” (1–14).

Yes Yes Yes Enter “15” to bypass answering machine.

No No No Enter “0”.

No Yes No Enter “0”.

No No Yes Enter 1–14.

No Yes Yes Enter 15. See Important Note below.

Important Note: If “15” is entered in field

✱

95 to bypass an answering machine, and a 4285 Phone

Module is included in the installation, you should note the following:

When calling in from an off-premises phone (to receive a status report or execute a command), the

user should make the initial call, allow 1 to 3 rings only, and hang up. Then call in again – the Phone

Module will now seize the line, and 2 long tones will be heard, followed by the usual voice prompt for

the 2-digit phone access code. If this procedure is not followed, Phone Module operation will not be

possible.

✱

96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No.

FOR DOWNLOADING (No data entry required; press

✱

96)

✱

97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES

(No data entry required; pressing

✱

97 automatically loads all Ademco

defaults). Do not use if previously programmed with other values.

TO EXIT

PROGRAMMING MODE

(

✱

98 or

✱

99)

✱

98 EXITS PROGRAMMING MODE and prevents re-entry by :

INSTALLER Code + 8 + 0 .

To enter the programming mode if

✱

98 was used to exit, you must

first power the system down. Then power up again, and depress [

✱

]

and [#] both at once, within 50 seconds of powering up.

✱

99 EXITS PROGRAMMING MODE and allows re-entry by:

INSTALLER Code + 8 + 0 or by method described in paragraph

above (power down, power up and depress [

✱

] and [#] both at once,

within 50 seconds of powering up.).

1 2 ... 14 15 16 17 18 19 20 21 22 23 24

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-10SE Manual de usuario Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE