ADEMCO VISTA 10 Manual de usuario descargar pdf (Pagina 4)

– 4 –

∗

∗∗

∗49 Split/Dual Reporting

[0]

0 = Standard/Backup reporting only (all to primary unless fail)

Primary Phone No. Secondary Phone No.

1 = Alarms, Restore, Cancel Others

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel All

4 = All except Open/Close, Test All

5 = All All

∗

∗∗

∗50 Burglary Dialer Delay

[2, 0]

Delay Time: Delay Time VISTA-10PSIA

0 = no delay UL: must be “0” Delay Disable

1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds

SIA Guidelines: delay must be minimum of 30 seconds

VISTA-10PSIA:

Delay Time: 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds

Delay Disable:

0 = use delay set in entry 1

1 = dial delay disabled for zones listed in zone list 6 (use zone list 6

to enter those zones that require dial delay to be disabled;

these zones ignore the setting in entry 1)

UL: Dial delay plus entry delay must not exceed one minute; use zone

list 6 to disable dial delay from appropriate zones, if necessary.

∗

∗∗

∗53 SESCOA/Radionics Select [0]

0 = Radionics (0-9, B-F), and all formats other than SESCOA

1 = SESCOA (0-9 only reporting)

∗

∗∗

∗54 Dynamic Signaling Delay

[0]

Delay selectable from 0 to 225 secs in 15-sec increments.

0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc

UL: Grade AA must be “0;” Grade A must be “15” max

∗

∗∗

∗55 Dynamic Signaling Priority

[0]

0 = Primary Dialer first; 1 = Long Range Radio first.

For UL Commercial Burglary installations that use a DACT and LRR,

this field must be “0”.

∗

∗∗

∗56 -*58 Menu Modes (see page 2 for description)

PROGRAMMING SYSTEM STATUS, & RESTORE REPORT CODES (∗

∗∗

∗59 -

∗

∗∗

∗68, ∗

∗∗

∗70 - ∗

∗∗

∗76, and ∗

∗∗

∗89):

For 3+1 or 4+1 Standard Format: Enter a code in the

first

box: 1–9, #+10 for

0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.

A 0 (

not

#+10) in the

first

box will disable a report. A 0 (

not

#+10) in the

second

box will result in automatic advance to the next field.

For Expanded or 4+2 Format: Enter codes in

both

boxes (1st and 2nd digits)

for 1–9, 0, or B–F, as described above.

A 0 (

not

#+10) in the

second

box will eliminate the expanded message for that

report. A 0 (

not

#+10) in

both

boxes will disable the report.

For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the

first

box, to enable zone to report (entries in the

second

boxes are ignored).

A 0 (

not

#+10) in the

first

box disables the report.

UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES

∗

∗∗

∗59 Exit Error Report Code [0]

See box above for entries. VISTA-10PSIA: [1] Always enabled.

∗

∗∗

∗60 Trouble Report Code [00] |

∗

∗∗

∗61 Bypass Report Code [00] |

∗

∗∗

∗62 AC Loss Report Code [00] |

∗

∗∗

∗63 Low Bat Report Code [00] |

∗

∗∗

∗64 Test Report Code [00] |

Use Scheduling mode to set periodic test reports or use the following

key commands to set schedule 2 to the stated repeat option (first test

report sent 12 hours after command):

installer code +[#] + [0] + 0 = test report sent every 24 hours

installer code +[#] + [0] + 1 = test report sent once per week

installer code +[#] + [0] + 2 = test report sent every 28 days

∗

∗∗

∗65 Open Report Code [0]

∗

∗∗

∗66 Arm Away/Stay Rpt Code

[0,0]

Away Stay

∗

∗∗

∗67 RF Trans. Low Bat Report Code [00] |

UL: must be enabled if wireless devices are used

∗

∗∗

∗68 Cancel Report Code [00] |

VISTA-10PSIA: [10] Report enabled.

∗

∗∗

∗69 Recent Closing Report Code [11] |

VISTA-10PSIA: Always enabled. Field does not apply to other controls.

RESTORE REPORT CODES

∗

∗∗

∗70 Alarm Restore Rpt Code [0]

∗

∗∗

∗71 Trouble Restore Rpt Code [00] |

∗

∗∗

∗72 Bypass Restore Rpt Code [00] |

∗

∗∗

∗73 AC Restore Rpt Code [00] |

∗

∗∗

∗74 Low Bat Restore Rpt Code [00] |

∗

∗∗

∗75 RF Trans. Lo Bat Rst Rpt Code [00] |

UL: must be enabled if wireless devices are used

∗

∗∗

∗76 Test Restore Rpt Code [00] |

OUTPUT AND SYSTEM SETUP

∗

∗∗

∗77 Daylight Savings Time [4][10]

Start/End Month

0 = Disabled; 1-9 = January-September (1 = Jan, 2 = Feb, etc)

#+10 = October; #+11 = November; #+12 = December

∗

∗∗

∗78 Daylight Savings Time [1][5]

Start/End Weekend

0 = disabled, 1 = first, 2 = second, 3 = third

4 = fourth, 5 = last, 6 = next to last, 7 = third to last

∗

∗∗

∗79 -*82 Menu Modes (see page 2 for description)

∗

∗∗

∗84 Auto Stay Arm

[1]

0 = no, 1 = yes, auto stay arm enabled

∗

∗∗

∗85 Cross Zone Timer [0]

This option not for use in UL installations.

0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min

1 = 30 seconds 7 = 3 min #+13 = 10 min

2 = 45 seconds 8 = 4 min #+14 = 12 min

3 = 60 seconds 9 = 5 min #+15 = 15 min

4 = 90 seconds #+10 = 6 min

5 = 2 minutes #+11 = 7 min

(assign cross zones on zone list 4, with *81 Menu mode)

∗

∗∗

∗86 Cancel Verify Keypad Display

[1]

0 = no, 1 = yes

∗

∗∗

∗87 Misc. Fault Delay Time [0]

(used with Configurable Zone Type “digit 6”)

0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min

1 = 30 seconds 7 = 3 min #+13 = 10 min

2 = 45 seconds 8 = 4 min #+14 = 12 min

3 = 60 seconds 9 = 5 min #+15 = 15 min

4 = 90 seconds #+10 = 6 min

5 = 2 minutes #+11 = 7 min

UL: may only be used on non-burglar alarm/ non-fire alarm zones

when used in fire and/or UL burglar alarm installation

∗

∗∗

∗88 Program Mode Lockout Options

[0]

0 = standard *98 installer code lockout

(reentry only by [∗] + [#] within 50 seconds after power up)

1 = lockout [∗] + [#] reentry after *98 exit

2 = not used

3 = lockout local programming after *98 exit (reentry by downloader only)

∗

∗∗

∗89 Event Log Full Report Code

[00]

See box above *59 for report code entries.

1 2 3 4 5 6 7 8 9 ... 15 16

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA 10 Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA 10