ADEMCO VISTA 10 Manual de usuario descargar pdf (Pagina 11)

– 11 –

01 Delete Zone?

0 = No 1 = Yes 0

0 = don’t delete zones; save zone list and return to the Zone List No. prompt.

1 = go to next prompt to delete zones

[∗] to continue

01 Zn to Delete?

(00 = Quit) 00

Enter each zone to be deleted from the list

01-64 = zones to be deleted from list followed by [∗] to accept each zone

00 when done to return to the Zone List No. prompt

NOTES:

• Any list may include any or all of the system's zone numbers.

• A zone list can be assigned to more than one output relay.

• When creating zone list 4 for cross zoning, include only zones assigned to zone types 3, 4, or 5. Do not include zones that have delays

(entry/exit zones, interior w/delay) or 24-hour zones, as these zone types may produce unpredictable operation and may not function as

intended. See field *85 for Cross Zone Timer option.

• Zone List 6: VISTA-10PSIA: See field *50 for Dial Delay Disable option.

• Zone List 7: VISTA-10PSIA: See field *93 for Unlimited Reports option.

*82 ZONE DESCRIPTOR PROGRAMMING MODE (press *82 while in Data Programming mode)

Program Alpha ?

0=No, 1=Yes 0

Press 1 to program descriptors.

0 = exit this mode

Custom Words ?

0=No, 1=Yes 00

To program standard alpha descriptors from the fixed vocabulary, press 0. The system will then

automatically display the descriptor for zone 1.

To define custom words (described below in “Adding Custom Words” section), press 1.

✱

ZN 01

Summary screen of zone 1 descriptor (if programmed) is displayed.

Press [∗] to start blinking cursor at zone number, then enter the zone number for which the descriptor is

being programmed.

• If a descriptor is programmed for that zone, it is displayed.

• To delete or change a previously programmed descriptor, press [∗] plus the same zone number. This will

clear that descriptor and move the cursor to the first word position.

• If you do not wish to change the existing descriptor, enter [∗] plus the next zone number for which you wish

to enter (or check) a descriptor. A summary display for that zone will appear. You must then press [∗] plus

the same zone number again to program a descriptor for that zone.

• If no descriptor has been programmed for that zone, the cursor moves to first word position.

✱

ZN 01

Select first word of descriptor:

Press [#] plus the 3-digit index number for the first word from the Alpha Vocabulary List. See index for entries.

Example: The descriptor that we wish to enter for zone 1 is BACK DOOR. From the list, BACK = 013.

Therefore, you would enter #013.

NOTE: If you enter the wrong word, simply press [#] plus the correct 3-digit number for the word you want.

✱

ZN 01 BACK

Save first word of descriptor:

6 = save word and go to next word in this descriptor

8 = save word and end descriptor if this is the only word used for the descriptor - go to summary screen

✱ ZN 01 BACK

D OOR

Enter the 3-digit number for the next word. In the example, the word is DOOR, whose number is “057.”

See index for entries.

[∗] to continue

✱ ZN 01 BACK

DOOR

Save second word of descriptor:

6 = save word and go to next word in this descriptor

8 = save word and end descriptor if this is the only word of the descriptor - go to summary screen

The two words in the example have now been entered. Note, however, that up to three words may be

entered (provided the number of characters will fit on the screen).

✱ ZN 01 BACK

DOOR

Summary Screen

The blinking cursor will disappear, indicating that the word(s) are stored in memory for that zone.

To enter a descriptor for the next zone, press [∗] plus the desired zone number (e.g., ∗02).

The summary display for that zone will appear.

Repeat the previous steps to enter the descriptor for the next zone.

To exit the Alpha descriptor mode, enter zone “00” at the summary display, which returns you to the

Program Alpha prompt. Enter “0” at that prompt to exit.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA 10 Manual de usuario Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA 10