ADEMCO Vista-20PCN Especificaciones Pagina 31
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
FIELD TITLE and DATA ENTRIES EXPLANATION
*60
Trouble Report Code
0 = no report
1st digit non-zero = send report
This will be sent if a zone has a trouble condition.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*61
Bypass Report Code
0 = no report
1st digit non-zero = send report
This will be sent when a zone is manually bypassed.
UL: Required for UL commercial burglar alarm installations.
*62
AC Loss Report Code
0 = no report
1st digit non-zero = send report
Timing of this report is random with up to a 4-hour delay. If AC
restores before the report goes out, there is no “AC RESTORE”
report.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*63
Low Bat Report Code
0 = no report
1st digit non-zero = send report
Sent when a low-battery condition exists in the system’s battery.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*64
Test Report Code
0 = no report
1st digit non-zero = send report
Sent periodically to test that the communicator and phone lines are
operational. Frequency of report is set in Scheduling mode (event 11).
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*65
Open Report Code
0 = no report
1st digit non-zero = send report
This is sent upon disarming of the system in the selected partitions.
UL: Required for UL commercial burglar alarm installations.
*66
Arm Away/Stay Report Code
0 = no report
1st digit non-zero = send report
This option allows for independent programming of Away and Stay
reports for each partition, including the common lobby.
NOTE: “OPEN” reports are not sent if the associated closing report
is not enabled.
*67
RF Trans. Low Batt. Report Code
0 = no report
1st digit non-zero = send report
Sent when a wireless transmitter low-battery condition exists.
UL installations: must be enabled if wireless devices are used.
*68
Cancel Report Code
0 = no report
1st digit non-zero = send report
This is sent upon disarming of the system after an alarm condition
was reported.
Restore Report Codes (
∗
70–
∗
76)
FIELD TITLE and DATA ENTRIES EXPLANATION
*70
Alarm Restore Report Code
0 = no report
non-zero = send report
Sent when an alarm zone is restored to its non-faulted condition.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*71
Trouble Restore Report Code
0 = no report
1st digit non-zero = send report
This is sent when a trouble in a zone is restored
UL: Required for UL commercial burglar alarm installations.
*72
Bypass Restore Report Code
0 = no report
1st digit non-zero = send report
This is sent when a zone that has been bypassed is unbypassed.
UL: Required for UL commercial burglar alarm installations.
*73
AC Restore Report Code
0 = no report
1st digit non-zero = send report
Sent when AC power has been restored after an AC power outage.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*74
Low Bat Restore Report Code
0 = no report
1st digit non-zero = send report
Sent when a system low-battery condition is restored to normal.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*75
RF Xmtr Low Batt. Restore Code
0 = no report
1st digit non-zero = send report
Sent when a transmitter’s low battery condition is restored (i.e., new
battery installed).
UL installations: must be enabled if wireless devices are used.
Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
*76
Test Restore Report Code
0 = no report
1st digit non-zero = send report
This is sent when the Test mode is exited.
UL: Required for UL commercial burglar alarm installations and
required for residential fire alarm installations.
4-5
- 9,67$39,67$3&1 1
- 9,67$39,67$3&1 1
- SOUNDING OF FIRE NOTIFICATION 2
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 6
- SECTION 2 7
- Cabinet and Lock 7
- Mounting the PC Board Alone 7
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Wiring the AC Transformer 10
- Backup Battery 11
- Earth Ground 11
- IMPORTANT: 12
- 4219/4229 Expansion Zones 13
- Installing a 5800TM Module 14
- Installing the Transmitters 14
- Installing the RF Receiver 14
- Installing a Keyswitch 15
- † Applies to VISTA-20P only 16
- † e.g., Altronix AX-RSB 17
- Installation Instructions 18
- Long Range Radio Connections 19
- AAV Connections 19
- Programming Overview 21
- Pager Programming 22
- Function Keys 23
- Output Devices 23
- Zone Type Definitions 23
- Mechanics of Programming 25
- Data Field Programming 27
- Zone Sounds & Timing ( 28
- Dialer Programming ( 29
- System Status Report Codes ( 30
- Restore Report Codes ( 31
- Miscellaneous System Fields 32
- Pager Programming Fields 34
- Zone Conditions Represented 37
- Keypad Programming Fields 38
- Zone Programming 39
- 41
- Completing Zone Programming 42
- Not Confirmed 45
- Output Device Programming 47
- Activated By 50
- Zone List 50
- Zone Type 50
- Zone Number 51
- Output Action 51
- Output Number 51
- Summary Screen 51
- Zone Lists 53
- Function Key Programming 55
- Alpha Descriptor Programming 57
- Adding Custom Words 59
- ALPHA VOCABULARY LIST 60
- Creating Schedules 61
- HH MMAM 62
- 0=NO 1=YES X 62
- System Communication 63
- Ademco Contact ID 64
- System Operation 67
- Stay zone list 68
- Panic Keys 69
- Testing the System 71
- Go/No Go Test Mode 72
- 1=DIAL, 0=WALK 73
- SECTION 14 75
- SECURITY CONTROL 75
- COMPATIBLE DEVICES 75
- System Sensor 76
- (Personal 77
- Emergency Transmitter) 77
- Regulatory Agency Statements 79
- UL NOTICES 80
- Limitations and Warranty 81
- (Continued) 82
- – NOTES – 83
- – INDEX – 85
- VISTA-20P/VISTA-15P 87
- ¬.§l 88
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-20PCN
(61 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS Guia de preparacion
(72 paginas)
(72 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN Guia de preparacion
(132 paginas)
(132 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(20 paginas)
(20 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales