ADEMCO VISTA-20SE Guía de usuario descargar pdf (Pagina 10)

Vista 20SEa Training Guide Page 10

4.1 Programming

* 8 Zones Hardwired

* Back to Base (Ademco Contact ID)

* Forced Arming

* Weekly test Reports

* Quick Arming

* 30 Secs Entry Time

* 8 Minutes Siren time out

* 70 Secs Exit Time

Field

Entry

Function ( comments )

Enter Programming Mode Press "

" & "#" within 50 Seconds of Power up OR Enter Installer Code (4112) + "8" + "0" + "0"

Pre Sets

* 9 7 Loads Factory Defaults

(Previous programming will be erased)

MUST BE DONE

Pre Sets

* 9 6

Resets the Subscriber Account number and CSID. MUST BE DONE

*20

Installer Code

(Default = 4 1 1 2)

*21

Quick Arm Enable

("1" = Yes, "0" = No)

*40

PABX Code:

(Only program for PABX access ie.. dial 0 to get a line)

*41

Primary Phone Number:

Enter up to 16 digits

(For local Alarms enter

*41*

)

*42

Secondary Phone Number:

Enter up to 16 digits (For local Alarms enter

*42*

)

*43

Primary Subscriber ID - Partition 1

(Enter 4 digits)

*44

Secondary Subscriber ID - Partition 1

(Enter 4 digits)

*45

Primary Subscriber ID Partition 2

(Enter 4 digits)

*46

Secondary Subscriber ID Partition 2

(Enter 4 digits)

*47

Phone System Select

("1" = Tone Dial, "0" = Pulse Dial)

*51

Periodic Test Report

("2" = weekly test reports, "1" = 24 hourly test reports)

*52

Test Report Offset

("0" = none, "1" = 6 hours, "2" = 12 hours, "3" = 18 hours)

*56

Interactive Field

Zone Assignment

(see Below)

*66

Arm Away/Stay Report Enable

("00" = disable report)

*94

Download Phone Number

*95

Ring Detection Count for Downloading

("# 15" = Answering System Defeat)

Exit

* 9 9

Exits Programming mode

Zone Assignment

For Zone Programming Enter *56 then Enter required Zone Number.

Zone Types

VISTA 20SEa Quickstart Programming Sheet

Follow this Guide to set up your Vista 20SEa with the following options:

To Enable Siren Monitoring, Cut Link on

Circuit board.

See Wiring diagram for more detail

ON IN STAY MODE

Type 01 Entry / Exit Burglary #1

Type 02 Entry / Exit Burglary #2

Type 03 Perimeter Burglary

OFF IN STAY MODE

Type 04 Interior Follower

Type 10 Interior with Delay

WIRELESS ONLY

Type 20 Arm - Stay

Type 21 Arm - Away

Type 22 Disarming

Type 23 No Alarm Response

Z n Z T P R C I n : L

0 1 0 1 01 1 0 HW: 1

Zn = Zone Number

ZT = Zone Type

RC = Report Code

In = Input Type

L = Response Time or

Loop Number

ZONE DEFAULTS

Zone 1 = (01) Entry / Exit Burglary #1

Zone 2 = (04) Interior Follower

Zone 3 = (03) Perimeter Burglary

Zone 4 = (03) Perimeter Burglary

Zone 5 = (03) Perimeter Burglary

Zone 6 = (03) Perimeter Burglary

Zone 7 = (03) Perimeter Burglary

Zone 8 = (03) Perimeter Burglary

Zone 9 = (05) Trb Day / Alm Ngt

Expansion Module Supervision

Zone 92 = Duress Enabled

Zone 99 = (06) 24 Hr Silent (* & #) Panic

24 HOUR ZONES

Type 05 Trouble Day / Alarm Night

Type 06 24 Hour Silent Alarm

Type 07 24 Hour Audible Alarm

Type 08 24 Hour Auxiliary Alarm

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 33 34

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-20SE Guía de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-20SE