ADEMCO Accord Especificaciones descargar pdf (Pagina 20)

Zone Programming  Group 3 Night Set

 The first digit entered is 3 for Night Set.

 The second digit is the zone number (1  8).

 The third digit is the zone type.

Example: In Programming Mode press 3 + 2 + 3. This

programmes zone 2 as an Intruder zone in the Night Set

mode and is accompanied by two beeps, indicating a

correct entry.

Note: The defaults programming is shown in brackets

in Table 3.3.

To review the programming: press the 3 key followed

by 00. The zone type is indicated on the keypad zone

LEDs (18) for zone 1 (accompanied by one beep),

then zone 2 (accompanied by one beep), etc.

Table 3.3 Night Set Group.

Programming System Options

System Programming  Group 4 System Options

 The first digit entered is 4 for System Options.

 The second digit is the required system option (1  8).

 The third digit is the option value.

Table 3.4 Group 4 System Options.

TESTHGIN

PUORGENOZ

ENOZ

EPYT

31)1(

32 )1(

33 )3(

34 )3(

35 )3(

36 )3(

37 )3(

38 )3(

SNOITPOMETSYS

PUORGNOITPOTLUAFED

4emiTtixE=9–1,tcatnoClaniF=0(emiTtixE=1 × .)s01)3(

4.)s01×emiTtixE=9–1(emiTyrtnE=2)3(

4eeS—emiTffo-tuClleB=3 5.3elbaT .semiTffo-tuClleB)8(

lanretnIdnadapyeK=2,dapyeK=1,tneliS=0(gninraWtixEteStraP=4

.)srednuoS

)0(

4.)seY=1,oN=0(teStraPniebortSdnaslleBlanretxE=5)1(

4.)seY=1,oN=0(teSthgiNniebortSdnaslleBlanretxE=6)1(

4eeS—tuptuOreggirT=7

stuptuOreggirT—7noitpO

.)3(

4)seY=1,oN=0(teSysaE=8)0(

Group 4  Option 1 Exit Time

This is the amount of time that the user has to exit the premises after the setting

procedure has been initiated. Entering 411 will set the Exit Time to 10 seconds, 412 =

20 seconds, 413 = 30 seconds, etc.  up to 419 = 90 seconds.

If final contact set is required, enter 410. This gives infinite Exit Time. The system will

only set when a Final Exit zone is closed after the exit timer has started.

Note: Exit Times for Part Set and Night Set are fixed at 30 seconds.

Group 4  Option 2 Entry Time

This is the amount of time that the user has to enter the premises and unset the

system. Entering 421 will set the Entry Time to 10 seconds, 422 = 20 seconds, etc. 

up to 429 = 90 seconds.

Note: Entry Times for Part Set and Night Set are fixed at 30 seconds.

Group 4  Option 3 Bell Cut-off Time

This is the amount of time that the sounders/bells activate after an alarm condition

has occurred. To programme the Bell Cut-off Time enter 43 then a number 0  9, see

Table 3.5 Bell Cut-off Times.

Note: Once the Bell Cut-off Time has expired the system will reset. Each zone is

allowed to cause an alarm condition twice during one set period. After this the

zone is automatically isolated.

Table 3.5 Bell Cut-off Times.

Group 4  Option 4 Part Set Exit Warning

This option allows the Part Set exit timer to be silent, audible through the keypad, or,

audible through the keypad and internal sounder. Night Set will always have a silent

exit timer but this option will affect the Night Set comfort tone (confirmation of set)

and fault warnings given at the end of the Exit Time; Tables 3.6 to 3.8 show all possible

options.

semiTffo-tuClleB

slleBsuounitnoC=0

etunim1=1

setunim2=2

setunim3=3

setunim4=4

setunim5=5

setunim01=6

setunim51=7

setunim02=8

setunim03=9

1 2 ... 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios

ADEMCO Accord Especificaciones Pagina 20

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Accord