ADEMCO Vista-10P Guía de usuario Pagina 31
- Pagina / 64
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
– 31 –
Security Codes & Authority Levels
Security Codes & Authority Levels Security Codes & Authority Levels
Security Codes & Authority Levels
(Cont.)
(Cont.)(Cont.)
(Cont.)
How to Assign
How to Assign How to Assign
How to Assign Security
Security Security
Security Codes and Attributes
Codes and AttributesCodes and Attributes
Codes and Attributes
The following lists the command strings for adding user codes and attributes.
Refer to the User Setup chart at the back of this manual for factory
assignments of user attributes and to keep a record of user programming.
Change System
System Master code + [8] + 02 + new Master code + new code again
Master Code The System Master code can be changed only by using the current
System Master code or by the Installer using the Installer code.
Add a User: System Master code + [8] + user no. + new user’s security code
User 01 = installer User 03-17 = standard users
User 02 = master (factory set master code is 1234)
The Keypad beeps once to confirm that new user was added.
Delete a User: System Master code + [8] + [user no.] + [#] [0]
The security code and all attributes set for this user number,
including any associated RF keys, are erased from the system.
Authority Level: System Master code + [8] + [user no.] + [#] [1]+ auth. level
Factory Assignments: Authority Levels (see definitions on previous page):
users 03-16 = 0 0 = standard user 2 = guest
1 = arm only 3 = duress
Access Group: System Master Code + [8] + [user no.] + [#] [2]+ group (1-8)
Factory Assignments: none You can assign users to a group, then set an access schedule that
defines the times this group of users can operate the system. The
system ignores these users outside the scheduled times.
RF Zone Number: System Master Code + [8] + [user no.] + [#] [4]+ zone no.
(adding a Key Fob) Use this command to assign a wireless button device (key fob) to a
user for arming/disarming functions (key fob must be enrolled in
system first; see your installer).
Factory Assignments: none Zone number: enter the zone number assigned to a button on the
key fob that will be used for arming/disarming by this user.
Deactivating a key fob: You can deactivate the arming/
disarming functions for a key fob (ex. if lost or stolen) by deleting
the associated key fob user. See “Delete a User” above. Other key
fob functions such as panic or device activation (if programmed)
remain active. To fully remove the programming for a key fob, see
your installer.
Pager On/Off: System Master Code + [8] + [user no.] + [#] [5] + 0 or 1
Factory Assignments: You can program a user so that a message is sent to a pager
users 01-16 = 1 (on) whenever this code is used to arm or disarm the system.
Paging On/Off: 1 = allow paging; 0 = no paging for this user
- ADEMCO VISTA-10P 1
- ADEMCO VISTA-10PSIA 1
- IMPORTANT! 2
- About This Manual 2
- Table of Contents 3
- System Overview 5
- (Continued)(Continued) 6
- General Information 8
- About The Keypads (Continued) 9
- Functions of the Keypads 10
- ✱] key, and 11
- Entry/Exit Delays 12
- (Contin(Contin 13
- (Continued) 13
- Arming the System 15
- GREEN RED 18
- Using the [OFF] key 19
- Bypassing Protection Zones 20
- Chime Mode 22
- Chime ModeChime Mode 22
- (Master Code) 23
- Panic Keys 24
- Panic KeysPanic Keys 24
- About Macro Keys 25
- (cont.)(cont.) 26
- Using Device Commands 27
- Paging Feature 28
- Paging FeaturePaging Feature 28
- (Cont.)(Cont.) 31
- Scheduling 32
- SchedulingScheduling 32
- Scheduling (continued) 33
- Event Logging Procedures 34
- Table of Event Log Codes 35
- Testing the System 36
- Trouble Conditions 37
- Any “beeping” that 38
- Total Power Failure 39
- Maintaining Your System 40
- (zone 95) 42
- (zone 99) 42
- (zone 96) 42
- Fire Alarm System (Continued) 43
- Emergency Evacuation 44
- Fixed-Word Display Keypads 46
- Alpha Display Keypads 47
- FCC Part 68 49
- Industry Canada 49
- Industrie Canada 49
- User Setup 51
- Paging Setup 51
- List of Output Devices 51
- – NOTES – 52
- A. GENERAL INFORMATION: 53
- (cont.) 54
- LIMITATIONS OF THIS SYSTEM 55
- – Notes – 56
- ÊK0736V4jŠ 64
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-10P
(112 paginas)
(56 paginas)
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales