ADEMCO 4110XM Especificaciones descargar pdf (Pagina 10)

-10-

11. Install Wireless Transmitters

• Select a House ID (all transmitters must be set to the same House ID as you will program

into the system). To determine a House ID that is not being used in a nearby system, use

the House ID Sniffer Mode (see Section 5: TESTING THE SYSTEM for further

instructions on using House ID Sniffer Mode).

• Determine what zone response type each transmitter will represent.

• Select each transmitter's zone number according to its zone response type (use the chart

below).

ZONE NUMBER (RF XMTR ID) ZONE TYPE

10-13 ENTRY/EXIT, Burg.

14-29 PERIMETER, Burg.

30-43 INT/FOLLOWER, Burg.

44, 45 INT w/DELAY, Burg.

46, 47 PERIMETER, Burg.

RF XMTR ID ZONE TYPE

48-55 FIRE

56-61 TROUBLE BY DAY/

ALARM BY NITE, Burg.

62 24 hr. (audible)

63 Programmed by field *92

• Set DIP switches on transmitters (according to each transmitter's instructions) for the zone

numbers and House ID selected (see DIP Switch Settings for Wireless Devices on page 17 of

this manual. Do not set two transmitters for the same zone number.

• Mark each transmitter's zone number so you can identify it easily when mounting.

• Program House ID and transmitter zone numbers into the system (see program fields *24

and *76 thru *92).

Do not permanently mount transmitters until transmission from each location has been

verified (see Section 5: TESTING THE SYSTEM for instructions on performing the Go/No Go

Test Mode.

––––––––––––––––––––––– WIRING GUIDELINES –––––––––––––––––

Aux Power Wire Run Chart

TOTAL CURRENT DRAWN BY ALL DEVICES* CONNECTED TO A SINGLE

WIRE RUN

Wire Size 50 mA or less 51 - 100 mA 101- 300 mA 301 - 500 mA

#22 500 ft (152m) 250 ft (76m) 80 ft (24m) 50 ft (15m)

#20 750 ft (228.6m) 380 ft (116m) 130 ft (39.6m) 80 ft (24m)

#18 1300 ft (396m) 650 ft (198m) 220 ft (67m) 130 ft (39.6m)

#16 1500 ft (457m) 1000 ft (305m) 330 ft (100.5m) 200 ft (70m)

* Includes Keypads, RF Receiver, and alarm devices requiring separate power.

Example: If you have two motion detectors that draw a total of 44 mA, and you are

using #20 AWG wire, the distance from the control panel Aux + and -

terminals to the last device can be up to 750 ft.

IMPORTANT

The combined length of all wire runs for devices connected to the

keypad data lines must not exceed 1500 feet (457m) when unshielded

quad conductor

cable is used (750 feet if shielded cable is used). This

restriction is due to the capacitive effect on the data lines when quad

cable is used.

Transformer Wiring Table

Distance of Transformer Wire Gauge

From the Control Panel To Use

Up to 50 feet # 20

50–100 feet # 18

100–250 feet # 16

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Comentarios a estos manuales

Sin comentarios

ADEMCO 4110XM Especificaciones Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4110XM