ADEMCO Vista-50 Guia de preparacion descargar pdf (Pagina 25)

Section 3 - Installing the Control

3-13

CONTROL PANEL

EXTENSION POLLING LOOP #1

4297

RPM

COMBINED INPUT AND EXTENSION LOOP LIMITS:

•

NO MORE THAN 77 DEVICES COMBINED ON THE INPUT LOOP AND EXTENSION

LOOP #1. NO MORE THAN 77 DEVICES COMBINED ON THE INPUT LOOP AND

EXTENSION LOOP #2.

• TOTAL LENGTH OF ALL WIRE RUNS ON THE INPUT LOOP AND EXTENSION LOOP #1

COMBINED CANNOT EXCEED 6400 FT. (3200 FT. IF USING UNSHIELDED WIRE IN

CONDUIT, OR SHIELDED WIRE). TOTAL LENGTH OF ALL WIRE RUNS ON THE INPUT

LOOP AND EXTENSION LOOP #2 COMBINED CANNOT EXCEED 6400 FT. (3200 FT. IF

USING UNSHIELDED WIRE IN CONDUIT, OR SHIELDED WIRE).

4297

RPM

INPUT POLLING LOOP

•

DO NOT CONNECT 4297 MODULES IN

SERIES (i.e., DO NOT CONNECT ONE

MODULE'S EXTENSION LOOP TO

ANOTHER MODULE'S INPUT LOOP.)

polling_loop-004-V2

EXTENSION POLLING LOOP #2

Figure 3-18: Polling Loop Connections Using Multiple Extender Modules

NOTE: The input loop limits stated in Figure 3-17 apply to Figure 3-18 as well.

Wireless Zone Expansion

The 5881ENHC RF Receiver and the 5869 Holdup

Switch Transmitter are listed for UL Commercial

Burglary applications. All other RF receivers and

transmitters are not listed for UL Commercial

Burglary applications.

The following table lists the receivers that may be used

and the number of zones they support.

5800 Series Receivers

Receiver Zones

5881L up to 8

5881M up to 16

5881H up to 86

In Canada, 5800 systems must use 5882 Series

receivers: 5882L/5882H. Information to the 5881

Receivers applies as well to the 5882 Receivers.

Both receivers use the same transmitters.

RF System Operation and Supervision

The 5800 RF system operation has the following

characteristics:

• The receiver responds to a frequency of 345MHz.

• The receiver has a nominal range of 200 feet.

• Supervised transmitters send a supervisory signal

every 70-90 minutes.

• Zones 88 and 90 are used to supervise the RF

reception of receivers 2 and 1, respectively. The

reception is supervised for two conditions:

1. The receiver goes “deaf” (doesn’t hear from any

transmitter) within a programmed interval of

time (defined by program field 1*30).

2. Proper RF reception is impeded (i.e., jamming

or other RF interference). The control checks

for this condition every 45 seconds.

A response type (05 Day/Night) must be

pro

rammed for zones 90 (1st receiver) and 88

(2nd receiver) for UL installations.

• The 5881ENHC receiver contains front and back

tampers that permit its use in commercial burglary

installations.

• You may only mount the 5881ENHC its own plastic

housing. Otherwise, the receiver constantly reports

a tamper condition.

• The control checks the receiver connections about

every 45 seconds. The receiver supervisory zone is

91 (1st receiver) and 89 (2nd receiver)

NOTE: The zone must be programmed with a

response type (e.g., type 05 Day/Night Trouble)

before the system supervises the connection to the

receiver.

• Use two identical receivers to provide either a

greater area of coverage or redundant protection.

They must be set for different addresses.

• Any zone from 1 to 86 can be used as a 5800 Series

wireless zone, with the exception of zone 64

(reserved for a wireless keypad).

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 111 112

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-50 Guia de preparacion Pagina 25

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-50