ADEMCO Vista-128FB Guia de preparacion Pagina 31
- Pagina / 147
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 3 - Installing the Control
3-9
-
+
-
+
-
+
EOL POWER
SUPERVISION
RELAY MODULE
A77-761B
4-WIRE SMOKE
DETECTORS
2000
OHM
EOLR
TO FIRE ZONE
TERMINALS
HEAT
DETECTOR
+
–
SHOWN POWERED.
RELAY OPENS WHEN
POWER IS LOST
333PRM-003-V0
POWER
SUPPLY
333 PRM
7
6
5
4
3
+
-2
+1
8
JUMPER
P1
USE A 12VDC,
BATTERY-BACKED,
UL LISTED POWER
SUPPLY.
JUMPER P1 ON
333 MODULE
MUST BE IN
"B" POSITION
FOUR-WIRE DETECTOR CIRCUIT
4204
CONTROL PANEL
234 112
76 4
Figure 3-12c: Wiring a 333PRM using a 4204 and a Power Supply
Using 2-Wire Latching Glassbreaks on Zone 8
Zone 8 can support 2-wire glassbreak detectors. The
zone provides enough standby current to power up to
50 2-wire glassbreak detectors meeting the
requirements listed below.
Compatible Glassbreak Detectors
Use detectors that meet the following ratings:
Standby
Voltage:
5VDC–13.8VDC
Standby
Resistance:
Greater than 20k ohms (equivalent
resistance of all detectors in parallel)
Alarm
Resistance:
Less than 1.1k ohms (see note below)
Alarm
Current:
2mA–10mA
Reset Time:
Less than 6 seconds
NOTES:
• You can use detectors that exceed 1.1k ohms in
alarm, provided they maintain a voltage drop of
less than 3.8 volts in alarm.
• The ADEMCO ASC-SS1 detector has been tested
and found to be compatible with these ratings.
21
22
GLASSBREAK
DETECTOR
ZONE 8
(+)
(-)
LATCHING TYPE GLASS
BREAK DETECTOR LOOP
2000
OHMS
EOLR
Figure 3-13: Wiring Latching Glassbreaks to Zone
8
• The alarm current provided by zone 8
supports only one glassbreak detector in the
alarmed state.
• Do not use other contacts when using
glassbreak detectors on zone 8. Other
contacts may prevent proper glassbreak
detector operation.
To wire 2-wire latching glassbreak detectors to zone 8,
perform the following steps:
Step Action
1 Select 2-wire glassbreak detectors that meet
the requirements stated previously.
2 Connect detectors across zone 8 (terminals
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128FB
Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista 5130XT Manual de usuario
(33 paginas)
(33 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista 5130XT Manual de usuario
(39 paginas)
(39 paginas)
(76 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista 5130XT Manual de usuario
(36 paginas)
(36 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA 5140XM Guía para resolver problemas
(14 paginas)
(14 paginas)
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales