ADEMCO 4140XMP Especificaciones descargar pdf (Pagina 33)

WIRELESS

“88”

or “90” sppcars In con-la display ~nd rapid

baeplng occurs

-..

. The reaiver is not mating any signals from aW of the

timsmitters in the system. An “88- is for Ihe 2nd r~’wec

a .90. is for the 1st r~iver. These dkplays am enabled

by =signing a zone ms~nse ty~ in pr~mm IieUs 1.08,

md 1.09. The r~mmended rasWnse is ekher zone tyw

~ or 07.

. Check that the antenna is inatalld properly and is not

shoned to any metal object, refer to WIRELESS

EXPANSION sedbn for details.

. Che& that the transmhters are ~wered up with fresh 9

vok batteries.

. Cheti that the house IDs match between transmhtem and

the rweiver.

. Detemine if anfihing is blocking transmission to the

receiver (8x. metal c~}ntis or shelves, etc.)

. If 428o is used, remove is cover. Pti the system in the

test mode, then see if lhe transmitters che&4n. If not,

move the receker to another -tion and @st Wain.

“8W’ or “’91”’ appears In co”~la display and rapid

beeping occurs

. The rti&er is nti res~nding to the hntml pmel. An .89-

refem to the semnd receiver and a .91. refam to the fimt

recaiver.

. h 428o is USW, cheti th~ the 428vs rover is on and the

magnet k in close pmximhy to the red swfich.

. ChW that the rnntml is wired pm~rly to tha reiver.

. ff 428o Is wed, detemine th~ the total mrrent dmw on the

pelting loop is not more than 64mA. If the draw does

exceed 64mA, install a 4197 loop etiender module, or

Wwer the 4280 frm amihary ~wer, as da=ri~.

..-.

. Che& that the wire run length is in agreemeti wfih the

r-mmetid wire gauge.

Zones, not programmed in the system, are

Indicating ‘“CHECK” conditions

. Chwk prqram fiekb .02 through .05, and 1.01 through

1.05

to make sure all unused zones ara 00s.

. CheM pwram fields 1“18 through 1”% to m~e sum that

dl inn-RF zones are 0s.

Zones indicating “NOT READW wndltion, but

transmitter contact loop Is Intact

. P@ the system in tha SNIFFER MODE for at le~t 2 houm,

to sea if another system in the area is using tha same

buse 10. ff so, change this system-s housa ID numbr.

. Make sure zones in questbn ara seleded as RF in fietis

1.16-1.25.

One or more transmitters are Indlcatlng “CHECK”

conditions after a while; console baaplng rapidly:

Check that the transmitters have the rnrreti house ID

pmgrammti.

Che& that the transmhtem have the mneti transmhter ID

assigned.

Check that the transminem have fresh batieries.

,.,-

“97” appaars In tha mnsole display and rapid

beaplng occurs

. Thk indtites that the ~lfing bp has etiher a direa shot,

or a sbfl to ground on the (+) sale. M!ght ako indbte that

the 4280 RF Ra-iver is -usina the shoti ldisrnnneti

426010 vei~).

. Chd that ~lling Imp Plarhy is mrr~ at the Qntrol

pnel, m well as at eati 4280.

. Check wntinufty from (+) side of the loop to ground

(di~nnm tk Plfiw Iwp from the bntml firstl) - an

own should b read (no rnntinuhy). ff a shofl to ground

exks, fid and efiminaa the shon.

. CheA voftage =mss tha Wiling &p at tha tintrol panel

as Weil as at each 4280, if used . there should be

fluaudion &meen 8-11 VDC.

‘“READY” display not going out when RF zones

faulted

Che& that the house IDs maid &ween tha transmittal

and the receber.

Console dlspiaya “NOT R~DY” but no zona IS

diaplayod whan ~] READY kay 18 dapres=d

. Chd p~ram fiefd .05 to m~e sure ~r h= a zone tyW

mspnsa enterad. ff a loop shoti oars and no resWnse

& entered for ’97, the console would display only “NOT

R~r. wfih M explanation.

CheM thd the recatier k en~led in pr~ram fields 1“26

for the fiti remtier and 1.27 for the ~rnnd remtier.

Ch% that the zones in question are enablad for RF in

~ram fiaMs 1.18 through 1.25.

Che* that a zone reswnsa is pmgmmmd for the zonas

~.$:,astion, in fields .02 through .05, and 1“01 through

CM that the r~kafs afienna b pmper~ installed.

Remove any sensors from tha transmhters and shon

-ss the transm~er temhals. Then fauh the transm’hter

m see i tha “READY ~iht goes om. If t does not go OM,

tie~ the programming for th~ panicular transmhten if it

doss go oti, ched the sensors on that zone.

tiva tha remher ti another Io=tbn for ~tter re~otbn.

. A Sileti Pank mndt”mn may & present. Kay tha security

de+ OFF to see f the rnnditbn cleam.

While in the “TEST mode, =me or

all of the

transmitters are not responding, or are

raapondlng irregularly

. The Test mde cws the r=eive~s senskiw by 507.. This

means that a long a a transmittal respnds, its Ioetbn

is satisfatio~.

. hve the affatiti transmtiers to another bation and ra-

test. There may M something bl=king its transmission

pah.

. ff all transmitters are affemad, mova tha raceiver to

another Io=tion. Thera may ba something blocking tis

r-ption.

. ff n? recaiver location can b found that can reliably

mcelva all tra,nsm~tters, add a se~”d receker in a

differant Iocatmn in the premises to axte”d the RF

mvemge of the system.

-29-

—

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 51 52

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMP Especificaciones Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMP