ADEMCO 4140XMP Especificaciones descargar pdf (Pagina 15)

SURFACE MoUNTING THE 4137/5137 CONSOLES

1. Use the template provided (On a separate sheet) to mak

the ~sfibns on the wall for the screw mounting hola$ and

.--.,

the ti~ut for the witing.

2, Pull the intetiam witing in the wall through the ~~ut.

3, Remove the mn~le,s back rover. me securing screw at

the front of the wnsole must be removti to release the

bab rnver

4. Pass the intetiace wiring throWh the opening in the ba~

rover, then mount the b~ wver to the wall suda~ with

screws.

5. Spfi~ the inteda~

wiring to the ~“SOIe ~i,eS (or to the

wires on the intati~ mnne~or supplid with 4137s),

Insulated solderless wire spfims (eg. 311) maybe USW

for spticing.

6. Mm the main my of the wn~le to the wall-mountad

back ~ver. The m“sole is properly attachad when i

snaps into place. Use the sacuring screw (previously

ramoved) to %cura the ~nsola to the ba~ rover

FLUSH MOUNTING WITH TRIM RING KIT {5137TRK)

1. Cut oti a 4sf4. Mgh by 8- wide opening in’ the wall ‘

bmween studs, no le~ than 1-1~- fmm eithar stud. Use

the templae provided to mark the ctiati,

2. Ir\sefl the four 1-1/2. long #6 screws through the

mounting holes in the Trim Rng and than attach tha four

metal securing clips, as shown in tho diagram. Use on~

two or threa t“fns of eati

smaw, allowing Iha metal cfi~

to hang

free~. Tha clips must not protrude beyond tha

sides of tha Ttim R“g or yo” will not be able to install the

Trk RIW imo the wt+ti in the nsfi SeD.

—

-0. WHFACEMOUmNOCO—

Install the ttim ring into the opening in the wall with the

hinge clasps to the right. MWing sure the tdm ring is

straight, tighten each clip screw, making sure that the

attached cli s(ties down inb its guide trati,

Install the Gnsole * follows: Engage the hinge clasps

on the ttim ring with the notties Imated in the b~ (right-

hand side) of the Gnsola’s front panel. Swing the left

side of the panel toward the ttim ting (the panel will PNO1

on the hinge clasps), and press firmly until the panel

.snms. ciosad.

5. Use the panel sewring screw (supplied with the tin~le)

to s-ure the Iefi

side of tha panel,

Figure 10. FLUSH MOUNnNG TNE REMOTS K~PADS

ADJUSTING THE ALPHA CONSOLE LCO VIEWING ANGLE (5137 ONLY)

Insen the end of the small, kefishaped tool (supplied) into

the small hole to the left of the rnnsole display window (the

=——

adjustment screw is recessed in this hole). Turn the

----

a~ustment screw to the left or tight until optimum viewing is

achieved, Be sure to take the height of the users into

atiunt when making this adjustment.

~ 0

.-. ... .

“’”’-I-

“-w

Figure ~1. ~JU~NG WE V!W ANGLMNSE~lNG THE NAMEPUTE

-15-

——

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 51 52

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMP Especificaciones Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMP